Examples of 'adhesion force' in a sentence
Meaning of "adhesion force"
adhesion force - this phrase refers to the strength of attraction between different substances or materials when they are in contact. It is commonly used in physics, chemistry, and material science to describe the bonding and sticking properties between surfaces
How to use "adhesion force" in a sentence
Basic
Advanced
adhesion force
The maximum adhesion force was measured.
Many times repositionable without loss of adhesion force.
Measure adhesion force.
A lower peel strength indicates a weaker adhesion force.
The mean adhesion force per sample strip is recorded as a function of displacement.
The use of optical tweezers in adhesion force measurements.
The adhesion force can be precisely manipulated so the powder can be easily removed.
A more detailed discussion of the adhesion force appears below.
The adhesion force is measured by the length over which the separation extends.
Limiting friction is a poor representation of the adhesion force in this case.
Said high adhesion force does not permit manual uncorking of the synthetic stopper.
Affixing the antenna on the ceramic line will lose the adhesion force.
This test characterizes the adhesion force between the support and zeolite.
Adhesion force was recorded as the maximum force observed during pull off testing.
All of these parts are made of carbon fibers and enhance the adhesion force.
See also
High adhesion force to steel that does not diminish even with multiple load changes.
The performance to prevent glass scattering can be controlled through control of adhesion force.
This force measures the adhesion force of the polymeric film attaching to the skin.
The reason why the combination stated above produces sufficient adhesion force is described below.
This instrument measured the adhesion force of the polymeric film attaching to the skin.
Adhesion force imaging In base configuration.
This substance exhibits superior adhesion force when reacted with moisture and is then cured.
However, the polyol also reduces the adhesion force.
This adhesion force depends on the energy delivered by the EB source.
The forces applied must be sufficient to overcome the adhesion force between adjacent towel surfaces.
When the higher adhesion force is required, the composition may be heat pressed.
The tackifier resin is resin which can give adhesion force to the adhesive agent layer.
In the case of the adhesive facies, the critical load characterises the adhesion force.
A decrease in median particle size increases the adhesion force between drug and carrier particles.
From the adhesion force distribution curve, a mean value of the forces has been derived.
To perform peel tests and determine the adhesion force in a Dynamometer at a certain speed.
Load-displacement curves that shows the effect of adhesion force.
After this soaking the adhesion force F is measured with the aforesaid adhesion test.
The higher the polarization energy, the greater the adhesion force.
Therefore, an accurate adhesion force can not be evaluated.
The larger such a change, the lower the durability of adhesion force.
First, the icephobicity implies low adhesion force between ice and the solid surface.
The larger the numerical value, the larger the adhesion force.
Further, the adhesion force was related to the % PEO in the membrane.
Non-ionic surfactants alone have shown moderate effects in adhesion force reductions.
The meat adhesion force was measured using an Instron device ( strip of 4 cm ).
To accomplish this, the pressure-sensitive adhesive must achieve comparatively high levels of adhesion force.
Adhesion force measured on inner Kraft paper to 12 µm thick HDPE foil.
If not mounted vertically, the float risks jamming adhesion force > buoyancy.
Adhesion force measured on outer Kraft paper to 12 µm thick HDPE foil.
This peel strength was used as a value to evaluate the adhesion force at 20°C.
The mean adhesion force for the peptide was approximately 300 pN.
ADH1 corresponds to the measurement of the adhesion force expressed in N / cm.
For this reason, the adhesion force with respect to the foaming mold 100 is increased.
The average value was set as an adhesion force [ unit, gF / cm ].
You'll also be interested in:
Examples of using Adhesion
Show more
Test for adhesion performance on wet surfaces
Transition from high to low adhesion surfaces
Very high adhesion and quick drying
Examples of using Force
Show more
With the sheer force of the blast
Force them to tell us where the shards are
Excessive use of force by law enforcement officials
