Examples of 'adjustment bolt' in a sentence
Meaning of "adjustment bolt"
Adjustment bolt: This refers to a type of bolt or screw that is used to make adjustments or fine-tuning in mechanical or structural components
How to use "adjustment bolt" in a sentence
Basic
Advanced
adjustment bolt
Lock the adjustment bolt with the nut.
Replace and tighten the vise adjustment bolt.
Install vise adjustment bolt into machine base.
The stationary vise can be repositioned by removing the vise adjustment bolt.
Bevel adjustment bolt on rear of saw.
Do not adjust the speed limit regulation bolt or the fuel adjustment bolt.
Adjustment bolt for control plate.
The repositioning of the air adjustment bolt will increase the amount of primary air.
An adjustment bolt connects one end of the wall panel to a foot assembly.
Loosen and remove angle adjustment bolt D.
The air adjustment bolt should now be properly aligned.
To adjust the stationary vise, remove the vise adjustment bolt.
Loosen adjustment bolt in front of the right rear wheel.
While holding motion control lever in place, loosen the adjustment bolt.
Tighten the adjustment bolt until it contacts the rack.
See also
The spring tension is adjusted by 4 steps for each turn of the adjustment bolt.
An air adjustment bolt is located on the chamber support bottom.
Loosen the locking nut on the ( vertical ) tilt adjustment bolt on the squeegee tongue.
Mount the adjustment bolt with the nut and washer.
If toward the left side of the deck, using wrench, turn the left adjustment bolt.
A separate adjustment bolt is provided for each section of the block.
To avoid serious personal injury, always tighten vise adjustment bolt securely before making a cut.
The depth adjustment bolt can be adjusted to change the depth of cut.
Slide the armrest into the receiver tube ( B ) on rear of frame until the adjustment bolt.
Loosen the angle adjustment bolt until the stem angle can be changed.
If the running belt drifts to the left, turn the left adjustment bolt 1/4 turn clockwise.
Locate the height adjustment bolt on the bottom hinge of the refrigerator door.
The armrest height is determined by the adjustment bolt ( A ) position.
Adjustment bolt tabs can be cut off for greater clear opening after installation.
Make sure the end of Height Adjustment Bolt 6mm does not protrude from the holder.
Adjustment bolt 24 and nuts 25 adjust the roller into frictional engagement with the belt.
Tighten the adjustment bolt securely 2.
A connection piece 25 is formed on the exhaust rocker arm 14e correspondingly to the gap adjustment bolt 24.
The air adjustment bolt is above the rectangular opening on the inner casing bottom.
Loosen the lock nut and turn the adjustment bolt counterclockwise Figure 43.
Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.
Do NOT remove ; ONLY loosen adjustment bolt 2.
For easier adjustment bolt access, remove the end caps.
The first flange 16 belongs to the first abutment element 12 and supports a first adjustment bolt 18.
Rotating the adjustment bolt one complete turn changes the clearance by 2 steps.
Turn the left adjustment screw clockwise 1/2 turn, and the right adjustment bolt counter clockwise 1/2 turn.
Grasp air adjustment bolt and pivot ( push ) air adjustment bolt away from yourself.
Tighten ( to increase ) or untighten ( to decrease ) the adjustment bolt H.
Height adjustment bolt 6mm Optional accessory.
If the length of Height Adjustment Bolt 6mm is insufficient, spread a thin plate beneath.
The adjustment bolt 28 is inserted through the yoke aperture and threaded into the yoke nut 48.
Turn a height adjustment bolt 6mm, and adjust the height of the holder.
Turn the adjustment bolt clockwise an additional 1/2 turn, then tighten the lock nut securely.
NOTE, The adjustment bolt on the PTO adjustment linkage uses left-hand threads.
A gap adjustment bolt 24 is threaded onto the other end of the auxiliary rocker arm 21.
You'll also be interested in:
Examples of using Bolt
Show more
Remove the bolt with a socket wrench
Bolt or clamp the saw to its support
Stiffener bracket bolt must be kept tightened
Examples of using Adjustment
Show more
Adjustment for accrued income from investments
The single flow adjustment knob allows
Adjustment for other accruals and liabilities
