Examples of 'adjustment nut' in a sentence
Meaning of "adjustment nut"
adjustment nut ~ A type of fastener or hardware component used to make fine adjustments or changes in the position or alignment of mechanical parts or equipment
How to use "adjustment nut" in a sentence
Basic
Advanced
adjustment nut
Loosen the adjustment nut before adjusting.
Tighten the fluid needle adjustment nut.
Adjustment nut has changed position.
Loose fluid needle adjustment nut.
The adjustment nut is on the outside.
Loosen set screws of torque adjustment nut on the gear reducer.
Turn the adjustment nut counterclockwise as indicated by the arrow.
Push the cord into the slot in the adjustment nut.
Turn the adjustment nut to lengthen or shorten the cable.
The pendulum disk is moved up or down by turning the adjustment nut.
An adjustment nut is threadably mounted on a back end of the guide bush.
There will now be a gap between the thumbscrew and the adjustment nut.
Turn the adjustment nut to the right to tighten the brake pedals.
There should now be a gap between the adjustment nut and the thumbscrew.
Turn the adjustment nut to the left to loosen the brake pedals.
See also
Push the cord into the slot in the adjustment nut of the cord retainer.
Tighten the adjustment nut with the upper leg in a horizontal position.
The torsional loads are resisted by a locking system that prevents the adjustment nut from rotating.
Loosen the adjustment nut until the upper leg starts moving.
First, loosen the plastic adjustment nut.
Tighten the adjustment nut of the elbow with the lower arm in a horizontal position.
Do not over-tighten the clutch adjustment nut.
Tighten the adjustment nut of the knee joint with the lower leg in a horizontal position.
Use the accessory socket wrench to loosen the zigzag width adjustment nut 2.
Hold adjustment nut in position with wrench and tighten jam nut securely against adjustment nut.
Re-tighten both the adjustment nut and mount lock bolt.
The adjustment nut also provides a load surface for the differential bearing under normal operation.
To lower one side of mower, loosen lift link adjustment nut on that side.
Loosen the adjustment nut until the head starts moving see Figure 3.
To raise one side of mower, tighten lift link adjustment nut on that side.
Loosen the adjustment nut until the lower leg starts moving see Figure 5.
Go back to Step 2 and tighten the adjustment nut.
Loosen the adjustment nut until the lower arm starts moving see Figure 7.
ONLY adjust the mechanism 's tightness with the mechanism adjustment nut.
Hold the adjustment nut tight with an Allen key, while tightening the lock nut.
Hence, each bore cross section set on the adjustment nut corresponds to a specific Gmaxx value.
Adjustment nut 30 is then preferably locked into place, preventing subsequent adjustment.
The inner race 64 plays a roll of an adjustment nut.
The single adjustment nut 32 is utilized for adjusting bearing preload.
The compression on torque spring 40 may be varied through the positioning of adjustment nut 42.
Three full turns of adjustment nut will change mower height about 1/8.
To adjust the axle, you will need a 19mm wrench to turn the adjustment nut.
The adjustment nut 32 is fixed to the guide bush sleeve 29 at a predetermined rotation angle.
Loosen the brake handle adjustment nut ( A ) by turning clockwise.
The adjustment nut 32 becomes rotatable to adjust the inner diameter of the guide bush 11.
Mm Allen key ( included ) 5 Position adjustment nut for conical stop.
Turn the adjustment nut until properly adjusted Figure 69.
Place the bean container ( 2 ) on the grinder body adjustment nut 5.
Screw the position adjustment nut ( 5 ) onto the bottom onto the conical stop 's screw thread.
Adjustment lock nut once the pressure gauge is between 12 and 14 lbs ., tighten adjustment nut.
You'll also be interested in:
Examples of using Nut
Show more
I am kind of a hard nut to crack in that department
A nut who knows a lot about bombs
Loosen the bottom nut to eliminate water
Examples of using Adjustment
Show more
Adjustment for accrued income from investments
The single flow adjustment knob allows
Adjustment for other accruals and liabilities
