Examples of 'amp fuse' in a sentence
Meaning of "amp fuse"
An amp fuse refers to a protective device or circuit breaker used to prevent damage to electrical circuits by limiting the flow of electrical current. It is designed to 'blow' or 'trip' when the current exceeds a certain threshold, thus breaking the circuit and preventing further damage or hazards
How to use "amp fuse" in a sentence
Basic
Advanced
amp fuse
Amp fuse at rear of generator control panel has melted open.
Reinstall the IS Amp fuse in the control panel.
They must be connected in series with a 5 Amp fuse.
Only use a 3 amp fuse with this appliance.
The mains socket must be protected by at least a 16 amp fuse.
When fitting a fused plug a 5 amp fuse should be fitted inside the plug.
A 1 Amp fuse must be installed in the line supply to the pump.
Have an electrician replace with a 15 amp fuse or circuit breaker.
Use only 8 Amp fuse to prevent serious damage.
Make sure that the socket is protected by a 10 amp fuse or higher.
The plug is fitted with a 5 amp fuse which is the recommended fuse for your machine.
If it becomes necessary to replace the fuse, use a 5 amp fuse for the red wire.
No Power to outlet . 5 amp fuse defective or blown Snap disc tripped or defective.
It must be wired into a fused, unswitched, fixed wiring connector fitted with a5 amp fuse.
Remove the 15 Amp fuse before working on or around the generator or transfer switch.
See also
To prevent battery drain, remove the 3 amp fuse from the low ambient heater.
A 5 amp fuse is fitted in this plug.
This plug is fitted with a 13 amp fuse UK only.
Observe that the 15 Amp fuse has been removed from the control panel for shipping.
The power in each user 's house is limited by a 6 Amp fuse.
A spare 15 amp fuse is located in the fuse box.
The plug is not correctly wired and 13 Amp fuse fitted.
Confirm 15 Amp fuse is installed in control panel.
Correct short circuit condition by replacing 7.5 Amp fuse in generator control panel.
Install 15 Amp fuse in control panel on generator.
In the case of direct connection to the battery, use at least a 30 Amp fuse.
Remove the 15 Amp fuse before working on or around.
Important, For your convenience this appliance is supplied complete with a plug incorporating a 13 amp fuse.
The generator 's 15 Amp fuse is critical to correct system operation.
Make sure that each 6 volt battery has a properly installed Power Wheels 30 amp fuse before charging.
Remove the 15 Amp fuse from the control panel.
Battery Connection, Install an inline fuse holder ( not included ) and a 3 Amp fuse not included.
Then install the 15 Amp fuse in the control panel.
Power Supply, The control head must be connected to a 12 VDC power supply using a 3 Amp fuse.
Remove the 15 Amp fuse and disconnect the battery from the generator.
If running in a 4 ohm master / slave configuration, an 80 amp fuse is required.
The generator 's 15 Amp fuse has been removed to prevent the unit from starting during shipping.
With this appliance, if a 13 amp plug is used a 13 amp fuse should be fitted.
Make sure the 7.5 Amp fuse is removed from the generator Control Panel.
The appliance is supplied with a standard 13 amp 3 pin plug fitted with a 13 amp fuse.
To remedy the problem, remove the 15 Amp fuse and disconnect the battery from the generator.
The appliance is supplied with a moulded 13 amp 3 pin mains plug fitted with a 13 amp fuse.
Has the 1 amp fuse blown open?
Each outlet is protected by a 15 Amp fuse.
And put a 40 amp fuse in its place.
UK Model Only - The cord is equipped with a 13 amp fuse.
So a 20 amp fuse would be good here.
Built 7 amp fuse.
The 7.5 amp fuse on the control panel protects the DC control circuit against overload Figure 3.1.
If blown, replace with a 15 amp fuse of the same type and rating.
