Examples of 'changeover switch' in a sentence
Meaning of "changeover switch"
A changeover switch is a device or mechanism used to switch between two sources of electrical power or supply. It is commonly used in situations where a backup power source needs to be activated in case of a power outage or when switching between different power sources is required
How to use "changeover switch" in a sentence
Basic
Advanced
changeover switch
Presents the changeover switch of the inverter.
The preceding algorithm has been used to refine this changeover switch.
Check that the changeover switch on the control.
This arrangement enables the motor to be controlled with a single control changeover switch.
The corresponding changeover switch is installed.
The changeover switch should be in this position when the water heater is in use.
These can be connected to get a changeover switch or other multiple switches.
Press changeover switch until the symbol appears in the display.
Consequently, a false operation of the display changeover switch occurs.
The channel changeover switch on the transmitter is wrongly set.
Measuring alternating current, Press changeover switch.
Set the changeover switch to forward to make the chuck turn clockwise screw driving.
The sensor process module 52 includes a changeover switch.
Usage of fuel changeover switch Fuel changeover switch consists of.
The operation is indicated schematically in Figure 1 by test unit 9 and changeover switch 10.
See also
Move the changeover switch to the blowing setting B.
At the time of a severe fade-out, the changeover switch 6 moves to position B.
Usage of fuel changeover switch Standard EG fuel changeover switch consists of.
The through channel of the T-piece 5 is connected to an electrically controllable changeover switch 7.
Said changeover switch is controlled by a control logic circuit 7.
The potential at the input of the changeover switch P4 is therefore higher than previously.
A changeover switch K 1 scans the outputs of these cells.
This electric wire is connected to a changeover switch ( not shown ) which is connected and disconnected.
The changeover switch portion 322 may include at least two changeover switches.
Fig . 4 presents the structure of one changeover switch 7 according to the invention.
Set the changeover switch to reverse to make the chuck turn counter-clockwise unscrewing.
FIG . 1 is a schematical representation of a changeover switch of known type using a dead point over-run device ;.
Here the changeover switch comprises two controlled switches connected in series, which are LGBT transistors.
In other words, the mode switching unit 78 is composed of a manual operating changeover switch 64.
Move the changeover switch to the vac/ shredding setting.
The input / output of the antenna is connected to a band-pass filter 10, connected to the changeover switch 3.
The outlet a of changeover switch 7 is connected to a second electrically controllable changeover switch 8.
FIG . 12 is a diagram illustrating a mode changeover switch.
Consequently, each changeover switch includes two separate switches for each phase.
As an example, FIG . 11 shows a switching device acting as a changeover switch.
Consequently, each changeover switch includes three separate switches for each phase.
FIG . 11 is a blow-up showing a switching device assembled as a changeover switch.
Change the MAIN / SUB changeover switch setting as described below Refer to figure 5.
The curve C 1 represents the value at the output S of the first changeover switch 13 ;.
Activate the changeover switch ( direction of rotation setting, transporting safety device ) 9.
When the battery 1 is being discharged, the changeover switch P7 earths the resistor R22.
Moreover, the changeover switch 130 has a plurality of switching modes corresponding to the light emitting states.
Grating-holder base 44 is a grating changeover switch on which several gratings 41 may be fixed.
The changeover switch 133 is changed over depending upon the signal specifying the results of discrimination.
A common contact of the changeover switch 46 is connected to the charging control means 47.
The changeover switch 64 is a manually operable sliding switch, a push-button switch, or another manually operated switch.
In the preferred example, a changeover switch 23 selects one oscillator between oscillators LOinf and LOsup.
This changeover switch K 2 scans in sequence M stages identical to that represented in FIG . 5.
The input E 2 of the first changeover switch 13 has a value representing the pitch angle θ ;.
Changeover switch for battery .6 temperature.
You'll also be interested in:
Examples of using Changeover
Show more
Fast changeover from one product to another
It ensures that the changeover is spread out
Changeover the same period of previous year
Examples of using Switch
Show more
The floating switch is blocking in automatic operation
Opera never survived the switch to electric
Set the switch to the correct position
