Examples of 'chip surface' in a sentence
Meaning of "chip surface"
chip surface - This phrase could refer to a microchip or integrated circuit embedded on a flat or smooth material surface. It may pertain to technology, electronics, or manufacturing processes
How to use "chip surface" in a sentence
Basic
Advanced
chip surface
A first antibody is bound to glass or polycarbonate chip surface.
Unique vinyl chip surface with a luxury look at minimum cost.
This was found to be technically complex if not impossible on a chip surface.
The sensor chip surface was regenerated after each analysis cycle.
This initially covers the whole of the chip surface.
In this way the chip surface can be prepared for a subsequent spotting process.
The antibody is then exposed to sclerostin bound to a chip surface.
Test antibodies are first bound to the sensor chip surface vía immobilised catching antibodies.
Subsequently the samples were injected over the sensor chip surface.
Dilutions of binders were floated over the chip surface and binding determined using BiaEval Software.
This solution is relatively expensive and takes up a large chip surface.
And moulded chip surface smooth, no effect on the vulcanization.
This solution is realtively expensive and takes up a large chip surface.
Moreover, the chip surface can be varied quite considerably.
First the hydrophilic properties are generated over the entire chip surface.
See also
Basically, a metal chip surface is coated with a silicon dioxide film.
A monolayer is formed when only one layer of molecules is formed on the chip surface.
The chip surface still appears black, because of the relatively low level of background fluorescence.
Alternatively channels drilled or etched into a manifold sealed to the chip surface could be used.
The activated chip surface was then capped with the addition of 1M ethanolamine.
The homogenous distribution of heating elements enables a uniform heating across the chip surface.
For comparison, HIM was also immobilized on chip surface by physical adsorption.
The microarray contains chemically synthesized oligonucleotides that are immobilized on chip surface 10.
The sensor chip surface was regenerated after each experiment by injecting 10 µL of 10 mM HCl.
The processing power of an IC becomes manifest in the quantity of chip surface área.
Figure 24-A now shows the entire chip surface producing intense red fluorescence.
Then a photo-structurable coating is applied to the chip surface.
Dissociation was measured by washing the chip surface with HBS buffer for 180 seconds.
As discussed above, singulation may be accomplished prior to assembling a bead array on a chip surface.
TNFR2-Fc VH 4 was covalently immobilized on to the sensor chip surface using amine coupling chemistry.
Purified mouse antibody preparations were captured on a polyclonal anti-mouse IgG antibody chip surface.
Regeneration of the chip surface between cycles was accomplished with two 30 second pulses of 3M MgCl2.
First, a fluorosilane compound is vapor-deposited on the chip surface as a monolayer.
The sensor chip surface was regenerated by an injection of 0.1 M phosphoric acid.
It also allows the real-time monitoring of release of molecules from the chip surface.
Dissociation was measured by washing the chip surface with HBS buffer for 180 sec.
Alternatively, Fn-binders can be immobilized as free proteins directly on a chip surface.
The individual chip surface adjacent to the wiper edge 19 is designated 21a.
After the chip-coupling antibody reached the target value, the chip surface was blocked.
Wet the chip surface by flowing over 300 mM KCl over chip / through channels.
Different methods may also be utilized for anchoring the Fn-binder on the chip surface.
Regeneration of the chip surface was reached by a short injection of HBS-P, pH 8.0.
These are located directly on the chip surface 13.
In Figure 3, a chip surface has been modified by attachment of a first monoclonal antibody ( mAb1 ).
Steps 4 through 7 are repeated on a fifth chip surface.
The chip surface was conditioned with three consecutive 1-minute injections of 1 M NaCl in 50 mM NaOH.
Soluble tissue factor was coupled at a pH of 4.5 to enable interaction with the chip surface.
Thereafter the chip surface was washed with HBS-P for 5 min. ( dissociation phase ).
Mask 16 is then removed from the chip surface S.
Following antibody immobilization, the reactive sensor chip surface was quenched using 1M ethanolamine hydrochloride / NaOH pH 8.5.
You'll also be interested in:
Examples of using Surface
Show more
An uneven surface increases the risk of overturning
Where ϑ is the measured test surface temperature
All feasible surface and subsurface ECVs
Examples of using Chip
Show more
Chip off the plaster and we split
Maybe you should chip in a little rent
Chip receiver for hedge trimmer use
