Examples of 'compression tests' in a sentence
Meaning of "compression tests"
Compression tests: These are experiments conducted to determine the compressive strength or ability of a material to withstand forces pushing towards its center. This is commonly used in engineering and materials science
How to use "compression tests" in a sentence
Basic
Advanced
compression tests
Hot compression tests are used to simulate forging.
By means of uniaxial and triaxial compression tests.
Results cf compression tests at zero speed.
The final volume is determined by preliminary compression tests.
Hot compression tests simulating forging operations have been performed.
The same equipment is used to perform compression tests.
So compression tests out good.
The geotechnical behavior was investigated by ciu triaxial compression tests.
Please find attached compression tests and technical specifications.
Compression tests will be carried out using a hydraulic testing machine.
Results of compression tests.
A rheological study of these two grades was based on dynamic compression tests.
Standardized compression tests can be used to characterize these foam parameters.
The material model is validated by a comparison of compression tests from literature.
The following compression tests were carried out on practice clip designs.
See also
This prototype has been validated under static and dynamic compression tests.
Compression tests were performed on samples cut from the setting experiment samples.
Shear tests were performed on butterfly specimens and compression tests were performed on cylindrical specimens.
Compression tests were also performed on the dogbone specimens after the tensile tests.
The rock matrix behavior is studied using triaxial compression tests on intact rock samples.
The compression tests were applied to determine the yield strength and the modulus of elasticity.
The permeability and the coefficient of consolidation were also determined during the compression tests.
The results of the axial compression tests on blocks were higher than the estimated strengths.
Five parameters involved in the model have been determined from mechanical and poromechanical compression tests.
Compression tests in the longitudinal and radial direction are improved and show a smaller distribution.
The material damage is quantified through triaxial compression tests with loading and unloading cycles.
The Young module mechanical resistance and stiffness was subsequently determined through compression tests.
Dynamic compression tests were carried out on a Split Hopkinson Pressure Bars apparatus.
The stabilized samples were tested with triaxial and uniaxial compression tests and oedometer tests.
To achieve validation, compression tests were performed on the facial part of an isolated head.
The yogurt cup mechanical performances are determined by compression tests referred as Top Load.
Axial tension and compression tests were performed on open-ended pipe piles.
Figure 7 shows the equipment used for uniaxial compression tests.
Strength and compression tests indicates that the affected material does not deviate from non-affected material.
You have just watched JoVE 's introduction to compression tests on hardened concrete.
The compression tests were performed in load control at a constant loading rate of 3.3N/sec.
Figure 7 shows the apparatus used for the uniaxial compression tests.
Similarly, video encoding and file compression tests also ran extremely quickly.
The polymers ' viscoelastic properties have been characterized with the dynamical compression tests.
Compression tests on plastic beakers, buckets, boxes, containers, barrels and similar dimensionally stable packaging.
A second experimental testing programme, consisting in cyclic sinusoidal compression tests has been performed.
All compression tests are performed under controlled displacement mode with a displacement rate of 100 nanometer / sec.
The apparatus is also advantageous in the case of shear-free, pure compression tests.
The results of the compression tests are shown in Fig . 4.
These experimental methods were performed before, during and after a number of triaxial compression tests.
Compression tests indicate that PGS can be compressed up to 70 % repeatedly without rupture Fig.
Conducts classification, consolidation, triaxial and unconfirmed compression tests on disturbed and undisturbed soils.
Compression tests from the room temperature to 900 °C under confining pressure were also performed.
For starters, here is the image that I used in each of the compression tests.
For sample A of plasticine, similar compression tests have been carried out at a temperature of 20 C.
You'll also be interested in:
Examples of using Tests
Show more
These tests are now not thought to be necessary
Your cooperation in these tests is greatly appreciated
God tests our faith in many ways
Examples of using Compression
Show more
Compression must take place before encryption
Provides engine compression braking at low speeds
Compression straps easily adjust to volume of content
