Examples of 'connected to terminal' in a sentence
Meaning of "connected to terminal"
The phrase 'connected to terminal' typically refers to a connection between a device or component and a terminal or point of connection in an electrical or electronic system. It indicates that the device is physically linked or wired to a specific point where electrical or data signals can be transmitted or received. For example, 'The cables are connected to the terminal to establish a network connection.'
How to use "connected to terminal" in a sentence
Basic
Advanced
connected to terminal
The ground cable must be connected to terminal.
Connected to terminal.
A picture display tube which is not further shown may be connected to terminal Vo.
The earth lead is connected to terminal marked with the symbol and.
Avalanche diode d has its cathode connected to node C and its anode connected to terminal B.
These fixed terminals B connected to terminal connection units URB via a specialized control channel CCS.
The input of these elements are connected to terminal 1.
Is antenna connected to terminal on the back of the set?
Therefore connection 1 of the door opener is connected to terminal.
The servo motor was connected to terminal 10 in the control module through these microswitches.
The negative pole of this power supply is connected to terminal 2.
T int / number - inlet points connected to terminal on the country territory Terminal.
However, power will still be supplied to the load connected to terminal T.
Concourse BConcourse B is directly connected to terminal 3, and is dedicated exclusively to Emirates.
The common negative pole of these outputs should be connected to terminal 20.
See also
Fuse F is connected to terminal 13 to provide protection against high current fault conditions.
These piers would subsequently be connected to Terminal 1.
Point 8 is also connected to terminal C via a diode D2 polarized in the manner shown.
The other terminal of winding 7 is connected to terminal Sn.
Its emitter is connected to terminal C and its collector to the base of transistor T1.
This hotel is located directly connected to Terminal 1.
The Squaire is directly connected to Terminal 1 of Frankfurt Airport through a pedestrian connecting corridor.
The shield of this wire is connected to terminal 16.
Is connected to terminal 34 of the control unit.
The source of transistor MN 8 is connected to terminal B of the supply voltage.
Ground terminal 41 of the microcontroller must generally be directly connected to terminal 32.
The Regal Airport Hotel is connected to Terminal 1 by a bridge.
The upper surface of region 21 is in contact with a metallization M 3 connected to terminal GK.
T S / number - inlet points connected to terminal on territory of another country S.
Midpoint 8 of this series connection is connected to terminal 4.
The output is connected to terminal 11 and is the.
The enabling input v of the comparator 8 is connected to terminal 12.
Heating network 32 is connected to terminal g of the electronic module.
The ground ( earth ) wire of the mains supply must be connected to terminal 7.
The Regal Airport Hotel is connected to Terminal 1 through a covered bridge.
After further flexing, the end 9 of the ribbon element is then connected to terminal block 10.
The end portions 7 are connected to terminal appendages 9 of the central body 8.
Check wiring and operation of On / Off devices connected to terminal 1 and 2.
Terminal 14 is connected to terminal I 1 and forms a reference terminal.
The collector terminal is connected to terminal T2.
A metallization M 13 connected to terminal + V is in contact with the base region of transistor T 2.
The anode of this diode is connected to terminal 62.
This output is connected to terminal 31 by an electric conductor 33.
The end of the wire is then connected to terminal 28.
Terminal 9 is connected to terminal 2 through a decoupling capacitor 10, of a value of 47 microfarads for example.
The gates of transistors TP 1 and TN 1 are connected to terminal BLTI of the inverter.
The two ends are connected to terminal resistors of 120Ω which is shown as figure 2.
Digital outputs should normally be connected to terminal 42 IS.
Terminal STPIN / is connected to terminal STPOUT / of the preceding block.
As is known in the art, more than one ONU could be connected to terminal 18.
You'll also be interested in:
Examples of using Connected
Show more
You are directly connected to three different murders
Connected switch is offline or not operating properly
The audio cable is connected to the headset
Examples of using Terminal
Show more
Oil storage terminal and port infrastructure
Police request a clearer path to the terminal
I saw a whole roomful of terminal cancer on my way in
