Examples of 'cross-members' in a sentence
Meaning of "cross-members"
cross-members (noun) - supportive structures that intersect or connect different parts of a framework or system, commonly used in engineering, architecture, or vehicle design to enhance rigidity and stability
Show more definitions
- plural of cross-member
How to use "cross-members" in a sentence
Basic
Advanced
cross-members
There are more ash cross-members at the base.
The cross-members must be provided with guide means.
The section may here also rest on the cross-members.
These two cross-members consist of rectilinear wires.
The bus bodywork is normally fastened to the subframe cross-members.
A pair of cross-members extend between the tubes.
Insecure or missing fixing of body / cab to chassis or cross-members and if symmetrical.
Advantageously the cross-members are used to support belt support roller means.
The frame comprised lightweight longitudinal channel and tubular cross-members.
The legs and transverse cross-members are substantially mutually identical.
These stresses affect the plates of the exchanger via the cross-members.
The axial members or cross-members can be flat banded fibers.
Reference will be made hereinafter to the second position of the pivoting cross-members 4.
It is possible for each of the cross-members to be provided with such a stiffener.
The cross-members are also suspended at the same elevation as the stringers.
See also
In a preferred construction, the cross-members are each connected to both facing plates.
These cross-members are made of composite material of high rigidity, preferably carbon.
Thus, a large number of rows of cross-members need to be welded between the plates.
The most important modification relates to the number of cross-members and of stays.
In general, cross-members may be provided linking the longitudinal frame members.
Short longitudinal beams can be joined to the cross-members for further reinforcement.
This may for example consist of elongate struts that are interconnected by cross-members.
For the sake of simplicity, the cross-members will hereinafter be referred to as bars.
Moreover, it is possible to greatly reduce the length of the outer longitudinal cross-members.
The cross-members are locked by the fiber structure thereof deforming in the locking portions.
The structure of the uprights and cross-members moreover presents complex specific shapes.
The roof prototypes consisted of an frp sandwich structure and glued aluminium cross-members.
Metal extensions or cross-members have long been used in bumpers because of their good rigidity.
Most preferably the facing plates and the plurality of cross-members are made of steel.
Located on the cross-members are a plurality of standard curved steel shanks which extend downwardly.
The steel bed utilizes four steel cross-members to reinforce the load floor.
The cross-members ensure the spacing of said profiles in order to ensure the rigidity thereof.
Obviously, in this case the thickness of the cross-members shall have suitable dimensions.
The cross-members do not interrupt the thermally insulating layer defined by the horizontal structural elements.
The facing plates and plurality of cross-members are preferably made from a high strength material.
The cross-members may be steel bars of substantially uniform cross-section along their entire length.
Depending on requirements, landing gear with two cross-members may thus possess one to four stiffeners.
The landing gear is then fastened to the aircraft via its front and rear cross-members.
The number of these cross-members obviously depends on the actual length of the panel unit.
Lattice mast 1 comprises three uprights assembled by a plurality of bracing cross-members extending between the uprights.
The core has thin cross-members going into magnetic saturation when the secondary coil quenches.
Advantageously, the cross-wise support elements include substantially horizontal cross-members and substantially vertical uprights.
Mount from cross-members tied to trusses.
Later models had fixed cross-members.
Only one of these cross-members 3 is visible in the drawing.
Cross-members having other cross-sectional shapes are contemplated.
The fuselage has GRP-balsa stiffening cross-members.
The ends of said cross-members are connected to vertical trusses 13.
These fingers 12 extend perpendicular to the longitudinal direction of the cross-members 4.
Thus, landing gear may include cross-members fastened to a fuselage.
