Examples of 'dry polymer' in a sentence
Meaning of "dry polymer"
dry polymer - This term typically denotes a type of polymer material that is in a dry or solid state, as opposed to a liquid or solution. Dry polymers are commonly used in various industries for applications such as coatings, adhesives, textiles, and construction, where their unique properties and versatility make them valuable materials
How to use "dry polymer" in a sentence
Basic
Advanced
dry polymer
Dry polymer powder was then removed and weighed.
Mass of dry polymer which.
All of the ppm values are based on dry polymer weight.
The dry polymer exits the extruder as a single strand.
The percentages are given on the basis of dry polymer to dry clay.
A dry polymer is recovered by azeotropic distillation of water and solvent.
The means for collecting the dry polymer product is not critical.
A dry polymer powder was recovered by spray drying the aqueous latex.
Premixing of the polymers into a dry polymer mixture may facilitate handling.
The dry polymer was redissolved in toluene and stored in the dark.
The result is expressed in g of salty physiological solution per gram of dry polymer.
Redissolve the dry polymer in toluene and store in the dark.
This measurement is taken by placing a drop of olive oil on a dry polymer film.
Voids were noticeable in the dry polymer particles through examination under a microscope.
Dry polymer in a flash tank is under mechanical stress which easily breaks the polymer.
See also
The typical latex emulsion polymers or dry polymer products do not offer this advantage.
These dry polymer particles are then precipitated from the dispersion by adding acetone.
Other methods involve extrusion of dry polymer powders and dry or liquid therapeutic agents.
The dry polymer material is weighed on a balance and the dry weight is recorded.
Melting point of the dry polymer by DSC technique.
The weight found is brought to 1 g of dry polymer.
Examination of dry polymer particles under a microscope showed a single void in each particle.
The liquid components then vaporized instantly, leaving the dry polymer powder.
The final dry polymer is prepared in the same way as Example 2.
Solvating ability is an essential pre-requisite for fast ion conduction in a dry polymer.
The properties of the resulting dry polymer particles are also shown in Table 1.
Such a membrane possesses “ hybrid ” characteristics between microporous separators and dry polymer membranes.
The EVCI dry polymer compositions are shown in Table 3.
Thus the starting material for step a in inventive examples 3 and 4 was a dry polymer mass.
The dry polymer is characterised by,.
In this case, it is not necessary to dry polymer A.
A portion of the dry polymer powder was readily redispersed in an aqueous solution at pH 8.5.
The formulations are presented on the basis of 100 parts of dry polymer.
Substantially dry polymer particles are obtained, with drying losses of about 15 % or less.
The formulations are given on the basis of 100 parts of dry polymer.
The dry polymer in the form of a powder was weighed and 78g of polymer obtained.
The absorption capacity is therefore taken to be higher than 200 g water / g of dry polymer.
The dry polymer was readily soluble in polar solvents, such as chloroform, tetrahydrofuran, and acetone.
The emulsion add-on was targeted for 20 % dry polymer based on the weight of dry substrate.
A method according to claim 10, characterized in that said composition is admixed with the dry polymer.
First, the dry polymer powder is mixed together with the API, for example, antibodies.
Carboxylate function, 1 % by weight relative to the dry polymer.
The final dry polymer product had an inherent viscosity of 1.68.
The polymer mixture was diluted to a dry polymer content of 0.1 % prior to use.
Dry polymer phase ;.
They are preferably used in amounts of between 15 and 25 % of the weight of dry polymer.
A dry polymer product, dissolved to 1.5 % concentration was added to the surface size composition.
The swelling ratio is expressed as, swelling = ( g swollen polymer-g dry polymer ) / g dry polymer.
Dry polymer was dissolved in tetrahydrofuran and filtered through a 0.5 and a 0.2 micron filter.
To 100 % The product was prepared by making a dry premix of calcite and dry polymer.
You'll also be interested in:
Examples of using Polymer
Show more
Injected polymer compound shell in three sizes
We seem to be a bit light in the polymer sciences
High resistance polymer flow indicator cover
Examples of using Dry
Show more
Dehumidifier does not dry the air as it should
Let it dry completely before starting it up again
Dehumidifi er does not dry the air as it should
