Examples of 'ethylene content' in a sentence
Meaning of "ethylene content"
ethylene content - This phrase refers to the measurement or concentration of ethylene, a colorless gas that is naturally produced by plants and fruits as a hormone, and is used in various industries
How to use "ethylene content" in a sentence
Basic
Advanced
ethylene content
Ethylene content of a polymer can be measured as follows.
Random copolymer with enhanced ethylene content.
High ethylene content propylene ethylene block copolymers.
This band characterizes the random ethylene content.
With increasing ethylene content the melting point is lowered.
Bananas are very sensitive to temperature changes and ethylene content.
A higher ethylene content results in a lower glass transition temperature.
A random copolymer with a high ethylene content and no additives.
Ethylene content in copolymer.
The product will typically be high in ethylene content relative to propylene.
The second component used in preparing the composition is one having a higher ethylene content.
The same applies for the ethylene content in the inventive terpolymer.
The shortest fragments are needed here to show the low ethylene content sections.
The ethylene content of the polymer is not disclosed in the Example.
When the low molecular chains have a high ethylene content the solubility is also increased.
See also
The higher ethylene content in GPR was seen in broadening of the melting range.
From the spectra the triad and dyad distributions and the ethylene content are calculated.
EVAL E type has a higher ethylene content that allows for greater flexibility and even easier processing.
The copolymer produced in this polymerization was analyzed for ethylene content by FTIR.
XCS is ethylene content of the XCS.
Thus, the tacticity is independent of ethylene content in the polymer.
Ethylene content is measured, as well as molecular weight on selected fractions.
XS is not critical and depends on the ethylene content desired for the end polymer.
The ethylene content of the semi-amorphous polymers can be measured as follows.
Polybutadiene rubbers ; and high ethylene content propylene ethylene block copolymers.
Higher ethylene content also increases mechanical strength, block resistance, and paraffin solubility.
Also usable are mixtures of EAO 's of varying ethylene content.
Thus, to increase the ethylene content of the copolymer, higher pressures are employed.
Another preferred class is mixtures of EAO 's of varying ethylene content.
Measurement of an ethylene content and a saponification degree of the ethylene-vinyl alcohol copolymer.
Figure 6 shows the desirability of having high ethylene content on CCS.
The polymer block ( ii ) has a high ethylene content and is therefore generally crystalline.
Ethylene content of the reactor, after reaching steady state, is maintained at the conditions specified.
All the later references to EVOH ethylene content will be in % per mol.
Furthermore, the ethylene content in the return line after oxidation was determined by gas chromatography.
The melt moldability of EVOH having an ethylene content of smaller than 5 mol % is poor.
As the ethylene content is reduced, the barrier properties to gases, flavors and solvents increase.
EPMATHMARKEREP The molar percentage of ethylene content was evaluated using the following equation,.
Ethylene content and degree of saponification of EVOH,.
Similar heat sealability to the film of Example 2 was exhibited by increasing the ethylene content.
Also, increasing the ethylene content inevitably reduces the heat resistance of the polymer.
EVOH materials also differ in melt index, even with the same ethylene content.
Ethylene content in the E-PVOH is determined by NMR analysis.
The concentrated suspension had an ethylene content of 10 % by volume.
Comonomer content Ethylene content in polypropylene was measured by Fourier transmission infrared spectroscopy ( FTIR ).
The copolymer of this embodiment is having an ethylene content of 6 wt. % or lower.
The ethylene content of both fraction ( A ) and the overall composition is measured by FTIR.
This is achieved even when ethylene content is in the range of 1 to 5 wt %.
Ethylene content in the polymer was obtained from by Fourier Transformation Infrared analysis ( FTIR ).
Copolymers having greater than about 30 % ethylene content are preferred.
You'll also be interested in:
Examples of using Content
Show more
On the product content and environmental release
Content management interfaces for web systems
Adjusts style and content when necessary
Examples of using Ethylene
Show more
Death by ethylene glycol does not arrive unheralded
Use is advantageously made of polyethylenes or of ethylene copolymers
This is ethylene oxide and perchloric acid
