Examples of 'evaporation temperature' in a sentence
Meaning of "evaporation temperature"
evaporation temperature - refers to the specific temperature at which a substance undergoes a phase change from a liquid to a gas through evaporation. This term is typically used in scientific or technical discussions related to thermodynamics or chemistry
How to use "evaporation temperature" in a sentence
Basic
Advanced
evaporation temperature
The evaporation temperature can also be varied.
This also results in a low evaporation temperature.
Different evaporation temperature range on request.
The actual cause of freezing is a low evaporation temperature.
The evaporation temperature will fall to relatively low temperatures.
Applicable in a wide evaporation temperature range.
The evaporation temperature is thereby prevented from decreasing any further.
Te is the current target evaporation temperature.
The evaporation temperature and the evaporation pressure remain constant.
Midpoint fluid evaporation temperature.
Water had its limitations as an alternative owing to its evaporation temperature.
Increase the evaporation temperature.
The activator sublimes or evaporates beyond its sublimation or evaporation temperature.
The evaporation temperature must thus be suited to the types of hydrocarbons to be removed.
This measures the pressure and automatically calculates the evaporation temperature.
See also
This gives the evaporation temperature time to increase to a level high enough to avoid freezing.
The drying temperature corresponds to at least the evaporation temperature of the solvent.
Auto Yes Evaporation temperature below the limit.
Means of maintaining these reflectors at a temperature higher than the evaporation temperature of the metal.
Auto Yes Evaporation temperature above the limit.
Conduction uniformly heats the product on the moving drying belt to a desired evaporation temperature.
For the fast and gentle drying at reduced evaporation temperature a vacuum system is required.
If the evaporation temperature is too low, the heat exchanger may freeze.
This fuzzy fieldbus foundation block controlled the evaporation temperature in the plant in real time.
This way, the evaporation temperature decreases and the condensation temperature increases.
The pressure can further be limited with pressure sensors and the evaporation temperature with a thermostat.
In other words, the evaporation temperature of the refrigerant is increased.
After a few seconds the display returns to the Evaporation Temperature in C.
Therefore, the evaporation temperature is increased, which results in an increase in the inlet pressure.
LP control stops the compressor when the evaporation temperature falls below a certain level.
Petrodiesel spilled on a roadway poses a hazard to vehicles, due to its high evaporation temperature.
The controller displays the evaporation temperature in C main screen.
Accordingly, it is possible to control an excessive rise in the evaporation temperature.
This will minimize the fall in evaporation temperature during the start-up.
The operation frequency of the compressor 160 may be decreased to increase the target evaporation temperature.
The main reasons that affect the evaporation temperature are as follows:.
TeS, Target evaporation temperature ( target control value during cooling operation ).
Thus, it is recommended when the solvent has an elevated evaporation temperature.
Use an antifreeze when the evaporation temperature is close to the liquid-side freezing point.
During dehumidification, the dehumidification capacity is large when the evaporation temperature is reduced.
This will prevent the evaporation temperature from decreasing, and thereby protect from freezing.
Then, control of the change in the setting of the evaporation temperature is described.
TeSo, Refrigerant evaporation temperature at rated cooling capacity.
The condensing pressure hence increases, and the fall in evaporation temperature will be prevented.
Advantageously, the evaporation temperature of the solvents is lower than the temperature T.
Then, control of a change in the setting of the evaporation temperature will be described.
Eventually, when the evaporation temperature reaches a pre-set level, the low-pressure control will stop the compressor.
Vaporisation is performed at a temperature below the evaporation temperature of the application material 50.
AREA 3, the evaporation temperature and, therefore, the evaporation pressure, are very low.
Instead, an actual current value of the evaporation temperature may also be used.
You'll also be interested in:
Examples of using Evaporation
Show more
Optimisation of evaporation plants and evaporator operation
The air is then cooled down by evaporation
Convenient rotary evaporation with full extendibility
Examples of using Temperature
Show more
Manufacturer of the separate temperature measuring equipment
Actual temperature below low temperature value
Select the desired temperature with and
