Examples of 'extrusion rate' in a sentence
Meaning of "extrusion rate"
extrusion rate - Refers to the speed or amount at which material is pushed or pulled through a die. This term is commonly used in manufacturing or engineering processes
How to use "extrusion rate" in a sentence
Basic
Advanced
extrusion rate
No changes in extrusion rate were observed.
Roller speed can be adjusted to substantially match the extrusion rate.
High extrusion rate.
They further disclose coating formulations of a low range of extrusion rate.
The extrusion rate thus is inversely related to the extent of cure.
Run the puller at a rate that slows the extrusion rate of the polymer foam.
A relatively slow extrusion rate and a rather high flow rate of coagulating liquid are preferred.
This situation occurs when the baking rate and the extrusion rate essentially match.
MELT INDEXThe extrusion rate of a material through a specified orifice under specified conditions.
B Product was too fluid to determine an extrusion rate.
These PPS resins differed in extrusion rate as shown in Table VIII below.
The extrusion rate was determined by measuring the quantity extruded in 60 seconds.
The film thickness can be adjusted by selecting the extrusion rate and BUR.
However, such extrusion rate increases have practical limitations.
Spin line take-up rates are dependent on the fiber dimensions and extrusion rate.
See also
At a given extrusion pressure, the extrusion rate typically slows with increased viscosity.
The extrusion rate was determined by measuring the time required for an extrusion of 80g precursor.
Interestingly, unlike the effect extrusion rate has on stress, its effect on strain is minimal.
We compare each pen based on criteria such as maneuverability, weight and the extrusion rate.
A room temperature vulcanizable silicone composition having improved extrusion rate and thixotropic behavior, comprising by weight,.
A foam structure of the larger cross-sectional size can usually be achieved at a higher extrusion rate.
The H+ extrusion rate was measured with BCECF as described before.
The main welding parameters are, Extrusion rate.
An extrusion rate equivalent to 2.5 meters per minute could be obtained.
The washed PPS from each run was filtered, dried, and tested for extrusion rate.
A solution extrusion rate not exceeding 20 m / min is preferably employed.
The winding-up rate corresponds to the extrusion rate and amounts to 4m/min.
However, the extrusion rate ratio may become smaller than 1.
Example II is repeated, on the understanding that the winding-up rate is 4x the extrusion rate.
A consistent and desired extrusion rate is important to high-quality, economical pipe / profile manufacturing.
Measured as pph based on a total extrusion rate of 60 kg / hour.
The extrusion rate is determined by measuring the quantity extruded applying a pressure 5 bar for 60 seconds.
C Product was not measured for an extrusion rate because it was a " stinker ".
The extrusion rate of the strand is 5 mm / s.
Preferred roller speeds for stretching are between about 10 % to about 20 % faster than the extrusion rate.
The instantaneous extrusion rate was determined to about 5.6 kgs / hr.
The extrusion rate was held constant at 160 pounds per hour.
A process according to claim 1 wherein the extrusion rate is from O. lcm / second to 1 metre / second.
The extrusion rate is about 2 kg / h.
Extrusion rate Er in g · min -1, measured according to a test Et defined in the description,.
Herein, the extrusion rate of the parison is preferably not less than 700 kg / hr.
The extrusion rate values obtained for runs 7-11 appear in TABLE I.
You'll also be interested in:
Examples of using Extrusion
Show more
This prevents extrusion of the anterior teeth
Extrusion and blow moulding of plastic materials
Extracting the product of extrusion as a continuous wire
Examples of using Rate
Show more
The mortality rate is certainly on the rise
Rate stations and assign audit points
Low literacy rate and school attendance
