Examples of 'finger tight' in a sentence
Meaning of "finger tight"
finger tight - This phrase is commonly used in the context of fastening bolts or screws manually without using any tools, to a point where the item being fastened is secure but not overly tightened, allowing for adjustments if needed
Show more definitions
- tightened using the fingers, and no tools, to a torque of about 15 to 20 inlb or 1.7 to 2.3 Nm
How to use "finger tight" in a sentence
Basic
Advanced
finger tight
Do not tighten more than finger tight.
Finger tight will do.
Tighten the lock nut finger tight.
Tighten finger tight and snug the contact nut with an appropriate wrench.
Make sure this connection is finger tight.
Tighten each screw finger tight or until spacers are snug against burner box walls.
Loosen the cover screw to finger tight.
Finger tight will do. These repairs were extremely successful.
The entire thing is assembled finger tight.
Install the Spark Plug finger tight in the cylinder head, then tighten.
Make sure all the connections are finger tight.
Her finger tight ♪ trouble was cooking ♪ and the teacher was not looking ♪.
Tighten guide bar nut finger tight only.
Reassemble, insert the duckbill into the housing ( Fig . 8 ) body and reinstall the cap finger tight.
Tighten the bar nuts finger tight only.
See also
Preferably, the set screw 30 is threaded into the bore as far as possible, finger tight.
Check the bulbs to be sure they are finger tight and in working order.
Secure the assembly by screwing the base onto the jar until finger tight.
Do not over-tighten it - finger tight is sufficient.
The motor shaft and thread the blade bolt in finger tight.
Tighten just to finger tight then turn 2-3 more times.
Screw end cap clockwise until it is finger tight.
Screw end cap clockwise until it is finger tight - DO NOT OVER-TIGHTEN.
Take the 4 shield screws and screw each one into the shield until finger tight.
Replace the Quik-Change blade clamp ( A ) Fig . 2 finger tight by turning it counter-clockwise.
When refitting the spark plug, screw it up until it is finger tight.
Tighten guide bar nuts finger tight only.
Tighten center rail bracket nuts, leaving the outer nuts finger tight.
Tighten the bolts finger tight.
Re-attach the hand to the shaft and turn the hand nut finger tight.
Tighten two nuts finger tight.
Tighten center rail bracket 8mm nuts, leaving the outer ones finger tight.
Tighten the nuts finger tight.
The Contact Points should be tightened one-half turn beyond finger tight 2A.
Replace filler plug finger tight.
Fit shims ( P ) and upper clamp ( Q ) over the outer tube and install bolts ( R ) finger tight.
Tighten the bar mounting nuts finger tight only P.
Loosen the bar retaining nuts so it is finger tight.
Before adjusting chain, make sure guide bar nuts are only finger tight see Figure 3, page 7.
Thread spring nut on carriage bolt unit finger tight.
I do not have a torque wrench so I use the two finger tight method.
Tighten mounting screws on X-Bar finger tight.
Handle them carefully to avoid pos - finger tight.
If needed, readjust guide bar nuts to finger tight only.
NOTE, When adjusting chain tension, make sure the bar knob is finger tight only.
With wrench, tighten nut 2 turns past finger tight.
With free hand, attach nut, finger tight.
Fit the chain cover knob ( 9 ) and tighten it finger tight.
Position the carter chain and clamp the nut ( 12 ) finger tight.
You'll also be interested in:
Examples of using Finger
Show more
Your finger will not even twitch
You will be down to finger nubs in a week
Finger tighten plug or with small wrench
Examples of using Tight
Show more
Angles to tight to figure out exact location
The measuring instrument is not water tight
A tight timeframe was proposed for the process
