Examples of 'flat blade screwdriver' in a sentence
Meaning of "flat blade screwdriver"
A flat blade screwdriver is a type of screwdriver that has a flat, rectangular shaped tip used for turning screws with a corresponding slot in the head
How to use "flat blade screwdriver" in a sentence
Basic
Advanced
flat blade screwdriver
Use flat blade screwdriver to turn valve.
This may require a flat blade screwdriver.
Flat blade screwdriver with insulated handle.
Pry off electrode with a flat blade screwdriver.
Slide a flat blade screwdriver between the.
For plug removal requiring use of flat blade screwdriver.
Insert a flat blade screwdriver under jammed nail.
Lift the inner door upwards using a flat blade screwdriver.
Stick flat blade screwdriver or wedge into the kerf.
Remove the duct knockouts using a flat blade screwdriver and a.
Use a flat blade screwdriver to pry back the hooks.
Remove the fuse holder assembly using a small flat blade screwdriver.
Small flat blade screwdriver for wall control connection.
Reinstall the cap and tighten with the flat blade screwdriver.
Small flat blade screwdriver for lifting out parts.
See also
Remove the old traction tire with a small flat blade screwdriver.
Insert a flat blade screwdriver through the slot on the side of.
Remove the duct knockouts using a flat blade screwdriver and a small hammer.
Insert a flat blade screwdriver through the shaft of the valve.
Carefully remove the seal head retainer from the upper tube with a flat blade screwdriver.
Use a small flat blade screwdriver to remove the lamp lens cover.
To remove the housing, press the lock upwards using a flat blade screwdriver.
Using a flat blade screwdriver pry off the electrode from each burner.
Removeplastic cap from top hinge bracket post . Use flat blade screwdriver to remove and.
Use a small flat blade screwdriver to turn the control clockwise to increase gain.
Secure the handle with the slotted Torx screws using a T25 Torx driver or flat blade screwdriver.
Remove cabinet plugs with flat blade screwdriver tip wrapped in masking tape.
A flat blade screwdriver can be used to rotate the pins as shown in Figure 9.
Screws with a flat blade screwdriver Fig.
Remove the screw using either a torx 20 or flat blade screwdriver.
Use a flat blade screwdriver to pry the dust cover away from the wheel.
To adjust these controls, use a small, flat blade screwdriver.
Use the flat blade screwdriver to push the driver blade to its top position.
Lift the tab to about 45º using a flat blade screwdriver.
Using a flat blade screwdriver or utility knife, remove the exhaust knockout.
Tighten the mounting brackets, using a flat blade screwdriver see figure 2.
Use a small, flat blade screwdriver or coin and carefully open the battery compartment.
You should therefore loosen this snap-in connection carefully, for example, with a flat blade screwdriver.
Use a flat blade screwdriver to lift the tabs on the front underside of the cover2.
Remove the 4 pre-mounted plugs with the aid of a flat blade screwdriver no. 3 from the leg.
Insert the tip of a narrow flat blade screwdriver between the metal clips at about a 40 angle.
Remove this screw using either a Torx T20 or flat blade screwdriver.
The tool may for example be a flat blade screwdriver slipping between a fin 33 and the rod 13.
Remove brush caps ( 2 ) using a flat blade screwdriver.
Adjusting tool, Flat blade screwdriver.
Tighten securely with a flat blade screwdriver Fig . 7.
You'll also be interested in:
Examples of using Screwdriver
Show more
Use a screwdriver to loosen the air shutter
Always take away the screwdriver or similars
Use a screwdriver to secure all wiring connections
Examples of using Flat
Show more
Staying to the flat instead of the ridges
A flat battery must be recharged as soon as possible
Run batteries flat before removing them
Examples of using Blade
Show more
Propeller blade must have cut it in half
This guy knew how to use a blade
Rotate the blade so it falls into place on
