Examples of 'flat washers' in a sentence
Meaning of "flat washers"
Flat washers are thin, circular metal or plastic disks with a hole in the middle. They are used to distribute the load of a threaded fastener, such as a screw or bolt, over a larger surface area. Flat washers can help prevent damage to the materials being fastened and provide stability
How to use "flat washers" in a sentence
Basic
Advanced
flat washers
Flat washers for wall anchors.
Inlet hoses with flat washers.
Flat washers or other adapters may over stress the wheel.
Net hoses with flat washers.
Slide flat washers onto axle past the small hole.
Fit diverter body using flat washers provided.
Install the flat washers and nuts to the hanger bolts.
Remove anchor screws and add flat washers provided.
Insert new flat washers into each end of the inlet hoses.
These screws were associated with the use of corresponding flat washers.
Wheel locking pins and flat washers for installing wheels.
Washer must be connected to water faucets with new inlet hoses with flat washers provided.
I solved this by buying flat washers to make up for the gap.
Flat washers are pre-installed at the factory.
Check that your water inlet hoses have flat washers at both ends.
See also
Make sure that the flat washers have been placed into the hose couplings.
Properly seat all four fill-hose flat washers.
Insert hex head bolts with flat washers through the saw base and.
Position flat washers between the bolt head and the fluid cooler basin flange.
Loosen and remove the two bolts and flat washers securing the belt guide.
If plastic flat washers are included in hardware package, place one flat washer over stem.
Are all four fill hose flat washers properly seated?
Partially insert 2 blade screws along with the lock washers and flat washers.
The screws fitted with flat washers are used where the screws were previously removed.
To avoid leaks, check that your water inlet hoses have flat washers at both ends.
Remove the hex screws and flat washers from the hardware pack in your manual bag.
Assemble motor and seal plate to pump body with nuts, flat washers and lock washers.
Star screws with flat washers and spring washers for I.
Slide a wheel onto the axle followed by one of the flat washers see Figure 3.
Use 8 screws and flat washers to fasten the bracket to the wall.
From the top with the slot head screw, flat washers and lock nut.
NOTE, flat washers are not required with all units.
Make sure washer drum is empty and flat washers have been placed into hose couplings.
The cable lug should be located between the two M5 stainless steel flat washers.
Locate 6 blade screws, lock washers and flat washers in one of the hardware packs.
Insert new flat washers ( supplied ) into each end of the inlet.
Remove the machine screw, flange lock nut and two flat washers from the clutch bail.
Use 12 screws and flat washers to secure the bracket to the floor.
The four ring sensors 60 are in the form of flat washers.
Insert carriage bolts and install the flat washers and hex nuts, tighten securely.
C Attach the rear stabilizer tube to the main frame using 2 bolts ( a ) and 2 flat washers b.
Inlet Hoses Insert new flat washers ( supplied ) into each end of the inlet hoses.
Assemble the legs ( g ) as shown using the nuts, bolts and flat washers provided.
Insert 2 bolts through 2 flat washers into holes on top cabinet floor.
Assemble the legs ( 5 ) using the nuts, bolts and flat washers from the.
Remove the hex screws ( a ) and flat washers ( b ) from the hardware pack in your manual bag.
Secure each leg post using two 8 x 2 ″ panhead screws, lock washers, and flat washers.
Secure from behind using flat washers and nuts . 6.
Make sure the flat washers are against the heads of screws ( R ) Fig . 9 inset.
Related Topics, flat washers.
You'll also be interested in:
Examples of using Washers
Show more
Use washers on both sides of the wall
Place nuts and washers onto bolts
All washers are shipped with engine oil
Examples of using Flat
Show more
Staying to the flat instead of the ridges
A flat battery must be recharged as soon as possible
Run batteries flat before removing them
