Examples of 'front housing' in a sentence
Meaning of "front housing"
The phrase 'front housing' can have multiple meanings depending on the context. It could refer to the front portion of a housing structure, such as the facade or entrance area. It may also refer to a housing development or project located in a prominent or desirable location. The exact meaning can vary based on the specific context and usage of the phrase
How to use "front housing" in a sentence
Basic
Advanced
front housing
Remove the front housing of the base.
Save them for reinstalling the front housing.
Separate the front housing of thermostat as shown on the picture.
Insert the atomizer valve into the front housing.
Front housing section.
The actuator rod may be mounted within the front housing.
Ensure front housing is securely fixed and insert the retaining screws.
Move the latch to the left and remove the front housing.
The housing has a front housing portion opposing a rear housing portion.
Always operate the saw with the insulated boot on the front housing.
The rubber front housing cover also serves as an assembly pin retention mechanism.
The trigger rod may be mounted within the front housing and tube.
Release front housing by gripping lower half of outer frame and pulling outwards then upwards.
The hooks are molded as part of a front housing through which the needle passes.
A printed circuit board is positioned between the partition and the front housing.
See also
Remove the back housing from the front housing by forcing a screwdriver in between them.
The locking means may comprise deflectable latches on the respective front housing members.
Grasp front housing with one hand and rear handle with the other hand.
Pry the front panel from the front housing and remove the switch button.
The front housing member may include a front wall and sidewalls to define an interior cavity.
The plunger sensor button has been withdrawn from its normal position in the front housing.
Put the front housing back to the base and lock the front housing with screw.
Remove the two back black covers and slide the front housing off the appliance.
The front housing member rotates about a hinge axis passing longitudinally through the pivot pin.
There is a detailed reproduction of the rotary snowplow ‘ s front housing.
The front housing 4 is made of resin material.
Using a small screwdriver, pry off the front housing carefully.
Front housing sleeve, can be screwed off for chan.
Continuously pry the front housing using the single-side screwdriver.
Replace and tension the band, and reassemble the front housing part.
A front housing which is screwed with said rear housing ;.
The rear housing 2b is detachably attached to the front housing 2a by a suitable hook means.
The front housing 50 has several openings to incorporate a plurality of input and output devices.
The sub-assembly may further comprise a front housing attached to the collet member.
The front housing 4 is used for covering the front surface of the circuit substrate 2.
This fits into a slot in the lower right-hand side of the front housing unit.
The front housing has a dome portion 4b extending radially at the circumference of the through hole 4a.
The housing has a front grip, a rear grip, and a front housing portion opposing a rear housing portion.
The front housing portion has a height H1 and the rear housing portion has a height H2.
Insert the piston and spring into the front housing figure R1.
In this embodiment, front housing 32 does not include an internal energy source.
Insert the piston and spring into the front housing figure L1.
The front housing 14 includes an opening 18 to permit the displayed image to be viewed therethrough.
Thread the spray nozzle onto the front housing and hand tighten figure R3.
The projections 7a to 7d are exposed outside of the front housing 4.
The front housing 11 is like a box with the rear surface thereof open.
The housing 3 accommodates an electroacoustic transducer 7 adjacent the front housing wall 6.
FIG . 20 is a perspective view of the front housing of a third embodiment of the device ;.
The through hole 4a is formed in the dome portion 4b of the front housing 4.
Insert a screwdriver between the front housing and the back housing of the appliance Fig . 17.
You'll also be interested in:
Examples of using Front
Show more
Acting all brave in front of your cousins
Front of flange even with front of surface
Found your car in front of his apartment
Examples of using Housing
Show more
Improved land and housing policies implemented
Housing systems for other livestock categories
Proportion of makeshift housing at the national level
