Examples of 'gearcase' in a sentence
Meaning of "gearcase"
gearcase (noun) - A protective enclosure or housing that contains gears or mechanical components, typically in machinery or automotive systems. Gearcases are designed to prevent contamination, reduce noise, and provide structural support for the gears within. This term is commonly used in engineering and manufacturing contexts
Show more definitions
- Alternative form of gear case
How to use "gearcase" in a sentence
Basic
Advanced
gearcase
Remove rear gearcase pulley by clamping locking.
Be sure handle lock remains in gearcase notch.
Slide the gearcase out of the tube.
Place new drive belt on gearcase pulley.
Gearcase output shaft is facing left on muffler cover.
Install new belt on front gearcase pulley.
Gearcase Grease Fitting Engrasdera de la caja de engranajes.
Remove belt from front gearcase pulley.
Lock gearcase power output shaft according to trimmer manufacturer 's instructions.
Place new belt on rear gearcase pulley.
Second, you must position the workpiece so that it does not interfere with the gearcase.
Loosen the gearcase clamp screw.
Loosen the screws and remove the gearcase.
Thread small end of threaded stud into gearcase output shaft by turning clockwise.
Remove the three screws from the gearcase.
See also
Replacement parts for any part of the gearcase assembly if defective in materials or workmanship.
Remove locking tool from gearcase.
Position the trimmer with the gearcase output shaft pointing up ; as shown in the illustration.
Disconnect cable from rear gearcase.
Over-lubricating may cause the gearcase to run slower, and may cause grease leakage from excessive.
Remove the index bolt from the gearcase.
Every 50 working hours inject the gearcase with gear grease under high pressure through hole C.
Remove the outer tube from the gearcase.
Figure 2 schematically represents the gearcase of figure 1, but with the cooling arrangement only ;.
Shaft not installed in powerhead or gearcase.
The whole is connected to the sump 1 of the gearcase by means of a flange attachment 16.
The cooling arrangement is still separate from the gearcase.
Water on the cutters may enter the gearcase and damage your machine.
Align the hole in the boss adapter with the guide slot in the gearcase.
Carry out the setting and the programming of the gearcase following the specific procedures.
Reattach return spring to rear baffle / rear gearcase.
When the pilot light lightens, the gearcase is no longer operative.
DO NOT remove upper adapter plate from gearcase.
To perform this operation, first remove the gearcase from the outer tube as follows.
Disconnect return spring from rear baffle / rear gearcase.
Press the ON / OFF key for 2 seconds and the gearcase will begin its lighting cycle.
Do not touch the hot surface of the unit such as cylinder, muffler and gearcase.
Attach the debris shield to the gearcase with the two M6 x 30 screws as.
The splined hole on Holder B must engage with the gearcase shaft.
Attach the blade guard to the gearcase with the two M6 × 30 screws as shown.
Second through fifth year limited warranty on gearcase assembly.
To perform this operation, first remove the gearcase from the outer tube See Fig . HT15.
The pathway then passes upwardly through a hole 24 in a horizontal web 26 formed on the gearcase.
Command Thrust gearcase.
The upper disaligned end of the containing framework 2 shows a housing 7 for the hydraulic gearcase 6.
Reattach return spring to rear baffl e / rear gearcase belt keeper.
GEAR CASE ( MA13 ) The reduction gears are lubricated by multipurpose, lithium-based grease in the gearcase.
Important, Do not tip unit on its back, or gearcase oil may leak out.
Install and center the safety clip on the gearcase shaft.
Clean up excess grease, then reassem-4 . ble the gearcase onto the outer tube.
