Examples of 'initiation temperature' in a sentence
Meaning of "initiation temperature"
initiation temperature: The specific temperature at which a process or reaction is triggered or initiated, often used in scientific or technical contexts
How to use "initiation temperature" in a sentence
Basic
Advanced
initiation temperature
The initiation temperature of cooling is not specifically limited.
This is the decolorization initiation temperature.
The reaction initiation temperature should be as low as possible.
Cr has been known to exhibit a high oxidation initiation temperature.
The same is true for the initiation temperature in the lean mixture.
Suitable microcapsules are those that melt at a particular initiation temperature.
The shrink initiation temperature is another key attribute of a preferred shrink film.
It is preferred that the solvent boil at or above the initiation temperature.
Using reduced melt initiation temperature values in the sequence to control the reaction.
The reaction temperature may be the same as the polymerization initiation temperature.
For determining the heat sealing initiation temperature it is referred to the example section.
The longer the alkyl chain, the higher the decolorization initiation temperature.
The heat generation initiation temperature of the positive electrode is preferably as high as possible.
Temperatures in the middle zones were kept near the optimal initiation temperature of the initiators.
The melt initiation temperature MIT is taken as the point of rapid onset of melting.
See also
Random copolymer composition with improved balance between sealing initiation temperature and melting point.
Furthermore, the seal initiation temperature is likely to be higher than desired.
Higher MFR leads to lower seal initiation temperature.
If the initiation temperature is low, the total amount of shrinkage must also be low.
As a result, the coloring initiation temperature can be increased.
Also, the gas temperature may be initially lower because the catalyst has a lower initiation temperature.
The initiation time and the initiation temperature of the reaction are too high ;.
The thermally-activated initiator 14 is provided at a temperature below its initiation temperature ( defined above ).
In one aspect, the initiation temperature for a contact step is different than the run temperature.
The temperature of the lower-temperature solution is below the initiation temperature of the initiator.
Therefore, the hot-forming initiation temperature is desirably the Ar3 point or more.
The reactor was pressured to 150 psig with nitrogen and then heated to the initiation temperature.
Growth commences at a so-called crystallization initiation temperature where the solution is pre-saturated.
The initiation temperature was 70°C and the suspension polymerization was allowed to proceed for 8 hours.
A fixable temperature range was defined between the fixing initiation temperature and the highest non-offset temperature.
The heat sealing initiation temperature ( SIT ) is the temperature where a sealing strength of > 5 N is reached.
The emulsion was then stirred and heated to the initiation temperature 32°C under a nitrogen atmosphere.
Accordingly good sealing properties are desired, like rather low heat sealing initiation temperature ( SIT ).
The method of claim 1, wherein the melt initiation temperature depression model implements the Flory equation.
This overlapped specimens temperature represents the seal initiation temperature ( S.I.T. ).
The decomposition initiation temperature is preferably 310°C or lower.
The melt flowable layer had an initiation temperature of 175°C.
The expandable layer had an initiation temperature of 145°C ( determined by DSC as described above ).
Polymerizations were run adiabatically once initiated, and the initiation temperature was kept between 40°C and 45°C.
SIT is the heat sealing initiation temperature ( SIT ) given in centigrade [ °C ] of the propylene copolymer ( P ).
Said composition having a seal initiation temperature lower than 110°C.
Heat sealing initiation temperature ( SIT ), General.
The shape of DSC curve indicates low seal initiation temperature and good sealing properties ( Fig . 4 ).
The films had a shrink initiation temperature of about 55°C.
The outer layers also contribute to a low seal initiation temperature ( 110°C ) and excellent hot tack properties.
You'll also be interested in:
Examples of using Temperature
Show more
Manufacturer of the separate temperature measuring equipment
Actual temperature below low temperature value
Select the desired temperature with and
Examples of using Initiation
Show more
Publicity regarding the initiation of arbitral proceedings
Initiation and exit of the editing function
Specify dates of initiation and termination of therapy
