Examples of 'initiator solution' in a sentence
Meaning of "initiator solution"
initiator solution: This phrase refers to a plan, idea, or action that serves as the starting point to solve a problem or address a situation
How to use "initiator solution" in a sentence
Basic
Advanced
initiator solution
The initiator solution was placed in a syringe pump.
The reactor internal temperature was maintained by adjusting the initiator solution flow.
This initiator solution was placed in a syringe pump.
At the end of this period there was added a further initiator solution of,.
The heated initiator solution was transferred to a heated addition funnel.
To the slurry was added, simultaneously, a monomer emulsion and a initiator solution.
The first initiator solution was added to the contents of the flask.
This is achieved by the rapid mixing of the monomer, aniline, and an initiator solution.
An initiator solution was added to the reaction vessel to start the polymerisation.
When the monomer emulsion feed is completed, the initiator solution is continued until finished.
This initiator solution was flushed with nitrogen by bubbling of nitrogen gas.
Continuously introducing the pre-emulsion of step b into a reactor containing an aqueous initiator solution or.
The initiator solution is added to this preneutralized mixture of solvent and butadiene.
After the vessel is charged, a concentrated thermal initiator solution is added to the addition funnel.
Additional initiator solution was added before the completion of the monomer addition.
See also
After the reaction mixture has reached a constant temperature, the prepared initiator solution is added.
The flow of the initiator solution was adjusted to the flow of the monomer.
The mixture was stirred for 5 minutes and then the initiator solution from Table 1 was added.
An initiator solution was prepared by mixing the following,.
After a suitable hold period, the initiator solution is added to the hot aqueous resin mixture.
The initiator solution was placed in a syringe pump fitted with a 5 ml syringe.
EXAMPLE 2 Polymerizations were run using the solubilized initiator solution generated in Example 1.
An equivalent amount of initiator solution is run continuously into the reactor for one hour.
Polymerization continues for another 30 minutes after completion of the initiator solution B feed.
The initiator solution is added and after 3 hours the reaction is complete.
Upon observing polymerization, the pre-emulsion solution and initiator solution A feeds are started.
Then, the initiator solution is added together with any remaining water.
After 30 hours polymerisation, the second half of the initiator solution is added.
More initiator solution may be added at the end of the monomer addition, if desired.
After 5 minutes, the initiator solution was added.
This initiator solution contains 0.1 mmoles of initiator per ml of solution.
A small shot of 3.4 grams of initiator solution was added to start the reaction.
An initiator solution was added dropwise at the same time over 300 minutes.
Add the styrene and the remaining initiator solution dropwise over 40 minutes.
Thereafter, initiator solution 1 was charged into the reaction flask and held for 15 minutes.
After the reaction mixture has reached a constant temperature of 72°C, the prepared initiator solution is added.
The suspension and initiator solution were purged with nitrogen gas for approximately 15 minutes.
Then an additional 147 milliliters of the initiator solution were added over 3 hours.
Milliliters initiator solution Hold time following initiator feed,.
The monomer mixture is added in 2 hours and the initiator solution in 2 hours, 15 minutes.
Ml portion of the initiator solution composed of, Potassium persulphate grams.
Add 520 parts of styrene and the remainder of the initiator solution dropwise over 60 minutes.
The monomer mixture and initiator solution were fed at a variable-decreasing rate specified in Figure 1 below.
Once 88.1 parts of TFE have reacted the second initiator solution is added.
The polymerization initiator solution was charged in a total amount of 120 mL.
Next, isoprene ( 12 ml ) was vacuum distilled from butylmagnesium and condensed into the initiator solution ( flask A ).
Ten minutes later, the second initiator solution was added, followed by a 2 minute hold.
An initiator solution containing sodium persulfate 1.9 g in water was sparged with nitrogen for ten minutes.
Acrylic acid and a 25 % sodium persulphate initiator solution were co-fed to the flask over 90 minutes.
The initiator solution was 4 grams of sodium persulphate and 50 grams of DI water.
You'll also be interested in:
Examples of using Solution
Show more
One proposed solution is sustained livelihood programmes
Find a ripe moment to propose solution or option
There is now a solution to most of these problems
Examples of using Initiator
Show more
The initiator is responsible for the room
Founding member and initiator of the association
An initiator of adrenarche has not yet been identified
