Examples of 'kω' in a sentence
Meaning of "kω"
kω (noun) - kilo-ohm, a unit of electrical resistance equal to 1000 ohms
How to use "kω" in a sentence
Basic
Advanced
kω
Resistance range kΩ.
The analog input stages are all 13 kΩ electronically balanced types on female XLR sockets.
In the illustrated embodiment the electrical circuit comprises a resistance of 2 kΩ.
Output impedance 1 kΩ Maximum output level PHONES.
The insulation resistance is acceptable if the resistance value is more than 10 kΩ.
A resistance variation of 3 kΩ actually represents a 2 mV wanted signal.
Input current Limited by an internal resistance of 2 kΩ.
Default 10 kΩ this is the sensor supplied with the thermostat.
Short bleeps will sound for resistances lower than a few kΩ and above 5Ω.
A 1 kΩ resistor is connected in-line with one of the copper strips.
According to measured value the reading will be in Ω, kΩ or MΩ.
An electric resistance of about 1 kΩ can for example be used to form electric load 28.
Input sensitivy for nominal level is 2 mV into 1 kΩ.
The variable potentiometer 8 has the value 10 kΩ of the multiturn cermet type.
The sensitivity of this sensor 1 therefore corresponds to 1 kΩ.
See also
V ohmic resistance ≥ 1 kΩ Corresponds to measuring range selected.
This equals the voltage noise of a 25 kΩ resistor.
HELLA recommends using 10 kΩ to keep the output current as low as possible.
The resistance between the two electrodes was 29 kΩ.
A PD indicates that it is standards-compliant by placing a 25 kΩ resistor between the powered pairs.
Minimum load resistor for the recorder output is 10 kΩ.
The output voltage was monitored with a 2.6 kΩ resistive voltage divider also made by Maxwell.
It will however require adjustment of pull-up resistances from 5 to 1 kΩ.
The voltage reference means also has a 150 kΩ resistor placed between the transistor N 2 and earth.
The cells1 thus constituted were discharged through a resistance of 15 kΩ.
The measurements have been carried out with 1 kΩ resistors in the emitters of T1 and D2.
The cells were discharged through a resistance of 15 kΩ.
Two matched 10 kΩ resistors are.
More preferably, the surface resistance is in the range of 1 kΩ to 8 kΩ.
One suitable resistor is a 6 kΩ resistor, capable of handling 5W.
They were discharged through a resistance of 62 kΩ.
Analog sensors 0-5 kΩ NTC resistors, photoresistors and potentiometers.
In a more preferred embodiment, this resistance is less than about 10 kΩ.
Values from 10 Ω to about 5 kΩ are within measurement range.
All impedances were kept below 5 kΩ.
The enclosed temperature sensors ( NTC rated 33 kΩ at 25 C ) can be connected to these analog inputs.
Electrode impedances were maintained below 10 kΩ.
Take note of that resistance in kΩ ( kilo-Ohms ).
Impedance was kept below 5 kΩ.
In such a case, a resistor Rb of the order of 1 kΩ is suitable.
The resistance between these two points is reduced by half, that is to say 1 kΩ.
Discharge the capacitor using a 100 kΩ resistor.
After these antennas have been dried their specific surface resistance is greater than 200 kΩ.
Precise indication of resistance between 1 kΩ and 2 TΩ.
Resistance measurement up to 4 kΩ.
If a channel is not used, it must be connected to an 8.2 kΩ resistor.
The binary input has an internal resistance Ri of 20 kΩ.
If a channel is not used, it must be fitted with an 8.2 kΩ resistance.
The correction resistor Rc had a resistance of 10 kΩ.
For a stable, interference-free measurement, a potentiometer value of ≤ 10 kΩ is recommended.
