Examples of 'length setting' in a sentence
Meaning of "length setting"
The phrase 'length setting' refers to the act of adjusting or determining the desired length of something. It often applies to settings or controls that allow users to choose the length of an object, such as hair clippers, sewing machines, or digital interfaces. This term is commonly used in the context of technology, fashion, and personal grooming, where precise length measurements or adjustments are required
How to use "length setting" in a sentence
Basic
Advanced
length setting
Choose the appropriate hair length setting.
The length setting for a new driver id shown below.
Press to enter the humidifying hose length setting mode.
The length setting for a new driver is shown below.
Turn the adjustment ring to the desired length setting.
Use this length setting to clip the whole head.
Check the adjustable nosepiece for proper screw length setting.
Turn the length setting adjuster to the desired length setting.
Removing the comb does not change the selected hair length setting.
Do not turn the length setting adjustment ring beyond the highest setting.
This feature prevents accidental changing of the length setting during trimming.
The length setting is shown on the right hand side next to the button.
If you are trimming for the first time start with the maximum comb length setting.
You can only change the length setting if the appliance is switched off.
Press the center of the dial to toggle between stitch width and stitch length setting.
See also
The length setting selected is the one right below the indicator on the.
The Braun also has the memory SafetyLock system which remembers the last length setting used.
The terminal length setting stays at zero until another value is set manually.
For instructions about setting the length see Length Setting.
The length setting is equal to the hair length that will remain after trimming.
Turn the Zoom Wheel to the desired trimming length setting.
The Length setting must be set properly for pixel mapping to work.
Changing this value changes the Lens Length setting accordingly.
The Length setting configures the MotionOrb for the number of strings attached.
Small Comb Large Comb setting hair length setting hair length.
Hair length setting Resulting hair length.
Select straight stitch, with a medium stitch length setting.
Easy stitch length setting - adjustment without lever by turn button.
Select the widest width setting, but a short length setting.
The pre-programmed stitch length setting is suitable for most of your sewing needs.
Do not slide the length selector beyond the highest hair length setting 5.
The current Tape Length setting is shown in the lower-left corner of the display.
Do not turn the length selector beyond the highest hair length setting 5.
Static length setting involves moving the tip of a tool to contact the stylus - see Figure 1.
When you remove the comb attachment, the hair length setting does not change.
NOTE The correct screw length setting is very important for trouble-free magazine operation.
This operation is carried out without changing the length setting of the connection rod 48.
The length setting for a new driver is shown in the Technical Data Table marked?, column T.
If you are trimming for the first time, start with the maximum trimming length setting 9.
Maximum trimming length setting ( 9 ) to familiarise yourself with the appliance.
If you trim for the first time, start with the maximum hair length setting 9.
Any stitch length setting from 1 to 5 will give you an open zig-zag stitch.
To create a ‘ stubble look ', trim with the beard trimming comb set to hair length setting 1.
The selected hair length setting does not change when you do this Fig . 6.
If you trim for the irst time, start with the maximum hair length setting 18mm.
Check for proper fastener length setting see “ Setting the fastener length ” page 8.
Slide the comb to the desired hair length setting Fig . 7.
Length setting Cutting length in mm ( approx . ) Hair trimmer Beard trimmer.
Turn the zoom wheel to select the desired length setting Fig . 6.
To save a length setting in the memory, press the ‘ M'button for 2 seconds.
You'll also be interested in:
Examples of using Setting
Show more
I am setting the bar low so we are not disappointed
Adjust the volume setting to an audible level
Setting the running date and time
Examples of using Length
Show more
Tubing length and elevation difference limits
Cut wire liner at the right length
Only the length of the journey differs
