Examples of 'load resistor' in a sentence
Meaning of "load resistor"
load resistor: In electrical engineering, a load resistor is a component used to introduce a specific amount of resistance into a circuit. It helps simulate the typical output load that a circuit may encounter in normal operation
How to use "load resistor" in a sentence
Basic
Advanced
load resistor
The load resistor temporarily lowers the network voltage.
The coil formed part of the plate load resistor.
The load resistor is connected to the transmission line in order to modify its load.
Check the connectors in the drive and the load resistor.
According to the invention the size of a load resistor is selected following a new design criterion.
The first choke is provided in parallel with the load resistor.
The dump load resistor may be configured so that energy is dissipated and not stored.
In this case it is common to replace the load resistor with a tuned circuit.
The load resistor re-attaches between the two open points of the equivalent circuit.
The resistive charge is formed by the load resistor of the receiving antenna.
The network analyzer procedure above does not include the food load resistor.
In addition, the dimensioning of the load resistor brings with it a high stray capacitance.
Load resistor electrically mounted between the first terminal and the third movable contact ; wherein,.
In addition, the resistive load consists of the load resistor of the antenna.
In this case, the load resistor undergoes the same temperature variation as the detector.
See also
FIGURE 1 is a schematic diagram of a wind turbine having a dump load resistor.
Remarks, The sensor and the load resistor forms a voltage divider.
FIG . 7 a complete integrated voltage multiplier with an also integrated load resistor.
Introducing a suitable load resistor RL across the transistor 's collector and ground will set the gain.
A first measurement signal U is obtained from the terminals of the first load resistor 32.
SITRANS I, a load resistor is already installed in the device.
The first pass-through MOSFET buffers a current supplied at the first load resistor node.
Minimum load resistor for the recorder output is 10 kΩ.
The third pass-through MOSFET buffering a current supplied at the second load resistor node.
The dump load resistor is connected to the connector 22.
Its emitter is coupled to the reference terminal 2 via an emitter load resistor R7.
The dump load resistor dissipates the power produced by the generator 20.
The drain of transistor T1 is connected to the supply voltage V0 via load resistor Rc.
A capacitor 96 is connected across the load resistor 94 and serves as a filter for the load current.
This causes a microcurrent to flow in the load resistor 16.
The load resistor RL is also assumed to be zero ( a short circuit ).
The excess power is dissipated vía the dump load resistor 54.
Resistor R11 is the load resistor of the comparator outlet stage.
The illustrated application consists in discharging the cells 20 and 21 alternately through a load resistor Rc.
A shut down voltage will develop across load resistor 42, as described herein.
A load resistor 36 has been depicted in series with the switch 38.
This may be facilitated by the addition of a load resistor 78 across the coil.
Non-CANBUS, the load resistor is needed for European brand vehicle.
In Fig . 2 this consumer is identified with a load resistor RL.
A load resistor 6 has been shown in series with the switch 38.
The collector electrode of transistor Q3 is coupled to ground vía a load resistor 64.
Controller chip 40 is connected to a load resistor vía the sense leads 42.
The load resistor 46 is coupled to differential amplifier transistor 42 and voltage follower transistor 26.
As a result, an electrical current flows into the load resistor R1.
The value of the load resistor 838 may be similarly chosen.
Resistor 44 is a normal load resistor.
The load resistor 44 is coupled to the differential amplifier transistor 40 and the voltage follower transistor 24.
A resistor 74 operates as a load resistor for the passive infrared detector 66.
Line 620 shows the current through the load resistor.
An optional load resistor 838 may also be electrically coupled in parallel across the secondary winding 836.
You'll also be interested in:
Examples of using Resistor
Show more
An external braking resistor can be connected if required
Resistor on the top of the protection cap
Integrated brake resistor without complicated wiring
Examples of using Load
Show more
You can load up to five discs at once
Suppose you walk by with a load of cement
Lower the load to the bottom point
