Examples of 'melt flow rate' in a sentence
Meaning of "melt flow rate"
melt flow rate: This is a term commonly used in the field of material science and engineering to describe the rate at which a molten material flows under specific conditions
How to use "melt flow rate" in a sentence
Basic
Advanced
melt flow rate
The melt flow rate is very low.
The same is true with respect to the melt flow rate.
Melt flow rate and impact properties were comparable.
Accordingly the melt flow rate is rather low.
Melt flow rate of the powder did not change.
The test for the melt flow rate is defined above.
Melt flow rate is expressed in grams per reference time.
Process for preparing polystyrene having a high melt flow rate.
A minimum change in melt flow rate indicates good process stabilization.
Peroxide cracking is a process for raising the melt flow rate of a polymer.
Melt flow rate is inversely proportional to the molecular weight of the polymer.
It is generally considered that a melt flow rate is inversely related to molecular weight.
A melt flow rate of a polymer is very dependent on a molecular weight of the polymer.
The upper limit of the melt flow rate is not particularly limited.
The injection molded article is preferably featured by a rather high melt flow rate.
See also
The melt flow rate is preliminary depending on the mean molecular weight.
On the other hand the melt flow rate should be not too high.
The melt flow rate mainly depends on the average molecular weight.
One of the selected physical properties of the polyolefin may be melt flow rate.
Finally the melt flow rate is given for some of the polymers.
Propylene homopolymer with reduced emission value and high melt flow rate.
The melt flow rate is mainly depending on the average molecular weight.
One may expect an indirect proportionality of maximum output versus melt flow rate.
A large increase in the melt flow rate indicates substantial chain degradation.
The polymeric processing additive is a resin that has a very high melt flow rate.
The melt flow rate greatly depends on the molecular weight of the polymers.
In order to achieve said result one needs a good melt flow rate of the polymer.
A minimum change in melt flow rate is favored and indicates good melt processing stabilization.
One requirement of the propylene homopolymer according to this invention is its melt flow rate.
The melt flow rate and the density of the material are decisive for strength properties.
One essential requirement of the inventive polypropylene composition is its increased melt flow rate.
The melt flow rate is determined for the pellets and for the corresponding fibers.
The present invention provides a process for preparing polystyrene having a high melt flow rate.
The melt flow rate was complete on a Tinius Olsen extrusion plastometer.
Further it is desired that the fiber reinforced composition has a rather high melt flow rate.
The melt flow rate is determined using ASTM Standard No.
Such a product has a lower melt viscosity than a product with a lower melt flow rate.
The intermediate melt flow rate can be an advantage for co-injection molding.
A gear pump between the metering and mixing zones stabilized the melt flow rate.
Generally, the lower the melt flow rate the more preferred.
This illustrates that the presence of dispersant may adversely affect melt flow rate measurements.
If the melt flow rate decreases, the preform injection temperature increases accordingly.
The unplasticized base polymer has good flexural properties but its melt flow rate is low.
Moreover, such increases in melt flow rate occurred at each extrusion temperature studied.
This invention relates to thermoplastic olefins which display unique melt flow rate and viscosity behavior.
When melt flow rate falls within these range, film formability is good.
Component D is preferably a high melt flow rate component.
The melt flow rate is a measured value of a polymer pellet sample immediately before melt-spinning.
Therefore, many researches have been conducted to advance a melt flow rate of a polymer.
High melt flow rate values indicate a polymeric melt of low viscosity, and vice versa.
You'll also be interested in:
Examples of using Melt
Show more
It will melt all over the floor
They are just gonna melt the icing
To melt the ice off your girl
Examples of using Flow
Show more
I let the anger flow right through me
The flow of information is a two way street
Insufficient air flow through burn grate
Examples of using Rate
Show more
The mortality rate is certainly on the rise
Rate stations and assign audit points
Low literacy rate and school attendance
