Examples of 'microhardness' in a sentence
Meaning of "microhardness"
Microhardness (noun): A measure of the hardness of a material obtained by forcing an indenter, usually a diamond, into the surface of the material under controlled conditions
Show more definitions
- The hardness of a very small area of the surface layer of a material.
How to use "microhardness" in a sentence
Basic
Advanced
microhardness
Microhardness values were significantly affected by the photoactivation p.
It should also be noted that the microhardness variations are insignificant.
Microhardness was evaluated in three types of the sample teeth.
The hardness mechanical propriety was analyzed by vickers microhardness tests.
Microhardness testers are precision instruments.
Microindention hardness is also called microindentation hardness or simply microhardness.
Automatic microhardness tester.
One manifestation of the modified microstructure is a greatly increased microhardness.
Continuous microhardness measurement.
Microhardness was checked on the rolled and solution treated bar samples.
Mechanical properties were evaluated by vickers microhardness measurements and tensile testing.
The microhardness of each reinforcing element was first of all measured as described below.
And lastly the samples hardness were checked by testing microhardness vickers.
The specimens were submitted to microhardness test and scanning electron microscopy analysis mev.
The solution treated titanium alloy specimens were subjected to microhardness tests.
See also
The characterization was performed using microhardness tests and techniques of optical and electron microscopy.
Ten specimens were collected and transversally cut for microhardness analysis.
This figure shows the effect on surface microhardness as the atomic percentage of silver increases.
After the heat treatments is observed a reduction in the ts values and an increased microhardness.
The mechanical properties were assessed based on vickers microhardness measurements and charpy impact tests.
The hardness and microhardness before and after the tests were measured using a vickers hardness tester.
The metallurgical characterization of weld overlays was done by vickers microhardness tests and optical micrographs.
Vickers Microhardness and Young module evolved well with rising temperature.
The impression can be of the type of those used for microhardness tests of materials.
Consequently, higher microhardness and tensile strength were acquired.
There is some disagreement in the literature regarding the load range applicable to microhardness testing.
A photochromic polyurethane coating that has acceptable Fischer microhardness and photochromic properties has now been discovered.
Heat treatment of ENP deposit will significantly increase the microhardness.
Vickers and Knoop microhardness tests.
Surface microhardness was assessed after 3 days.
Later, they were evaluated by confocal laser microscopy and microhardness knoop.
Uc is the average value of the microhardness of the reinforcing element measured,.
A microhardness study was done in whole welded zone, including all regions of heated affected zone.
Procedure 2 determines the microhardness of the metal phase.
Additionally, microhardness values vary with load and work-hardening effects of materials.
Their offspring 's teeth were used to assess the microhardness of dental tissues.
The microhardness of the remaining surface is reduced, increasing the susceptibility to physical wear.
According to first observations, the microhardness of an unsintered coating on a magnesium alloy may e . g.
The optical microscopy techniques, sem / eds and vickers microhardness test were used.
Vickers microhardness values were higher for m-wire niti alloy, while control group had a higher toughness.
Analyses of the macrostructure and microstructure, as well as microhardness profiles and quantification of phases.
For products generated, the sinter samples also were subjected to the determination of vickers microhardness.
This resulted in a smooth sheet, which was used for microhardness and photochromic testing.
Finally, we present a method for measuring the recrystallized volume fraction by measuring the microhardness.
To analyze the effect of processing conditions, geometrical, microhardness and microstructural analyses are conducted.
The results of the microhardness measurement conducted by the inventor are presented on FIG . 5.
To obtain the mechanical properties tensile tests, vickers microhardness and impact were performed.
For the microshear-bond and microhardness the samples were included in acrylic resin and then polished.
A leading specialist in solutions for coating thickness measurement, material analysis, microhardness and material testing.
However, the Knoop microhardness measurements revealed significant differences between the coatings.
