Examples of 'milliq water' in a sentence
Meaning of "milliq water"
milliq water: MilliQ water is ultrapure water produced by a water purification system known as Milli-Q. It is free of ions, organic molecules, bacteria, and particulates, making it suitable for use in laboratories for various applications such as experiments, cleaning equipment, and preparing solutions
How to use "milliq water" in a sentence
Basic
Advanced
milliq water
The residue was reconstituted with MilliQ water.
Carry out repeated addition of MilliQ water and filtration of the collected retentate.
All solutions were prepared using ultrapure MilliQ water.
Repeated addition of MilliQ water and filtration of the collected retentate was carried out.
All the solutions were made up with MilliQ water.
MilliQ water served as a negative control.
All buffers were prepared with MilliQ water volumetrically.
Particles were separated by centrifugation and washed three times with MilliQ water.
The effluent MilliQ water is then tested for pH, and conductivity.
As negative control we applied MilliQ water.
Briefly, 26µl autoclaved MilliQ water was added to the sequencing reaction.
The enzyme beads are washed with MilliQ water.
Samples were diluted to 1 mg / ml in MilliQ water before injection on the RPC column.
Particle size measurement medium for all samples was MilliQ water.
MilliQ water means water which was filtered through transfer system with 0.2µm filter.
See also
For higher peptide concentrations peptides were dissolved in milliQ water by vortexing.
Add 9 ml of sterile MilliQ water to a sterile 15 ml conical tube.
The solution was diluted with 6 ml MilliQ water.
As a control, 150 µl pure milliQ water without DNase was added.
After the transfer, the membrane is rinsed for a few seconds with milliQ water.
After each step, the substrate was rinsed with milliQ water and dried under nitrogen flow.
Nanoparticle suspensions were washed 3 times using cycles of centrifugation and re-suspending nanoparticles in MilliQ water.
Small adjustments in conductivity were made by addition of MilliQ water when needed after titration.
Elution of G-CSF is performed by applying a step gradient of MilliQ water.
The crystal violet was removed and 300 µl milliQ water was added to rinse the wells.
Set up a Milliflex manifold with Milliflex MicroStar units containing about 50 ml of sterile MilliQ water.
The enzyme solutions were aspirated and 300 µl milliQ water was added to rinse the wells.
Materials used, All solutions are prepared with analytical grade chemicals and milliQ water.
The purified product was finally diluted in milliQ water ( 50 mL ) and freeze-dried.
The conductivity of the supernatant was decreased to less than 10mS/cm by adding MilliQ water.
Plates were washed three times with MilliQ water and dried by centrifugation ( 1 minute at 400 rpm ).
Five milligrams of particles were dispersed in 0.5 ml of MilliQ water.
Resulting pellets were washed 4 times with MilliQ water at 30°C and centrifuged as above.
The pellet thus obtained is taken up in 40 ul of MilliQ water.
Labelling tests were carried out using 2 mg / mL MilliQ water solutions of Bis DOTA-C3.
A 100 % soluble standard for each concentration is prepared by dissolving the peptide in MilliQ water.
Dilute the remaining retentate with MilliQ water to 4 ml.
Cells were washed by fully resuspending cells with 50 mL sterile MilliQ water.
After 12 minutes, the specimens were rinsed with MilliQ water before being dried.
The total volume was adjusted to 20 µl by adding MilliQ water.
The flow-through was discarded and 2 ml milliQ water added.
A series of increasing concentrations of peptide ( 2 to 400 µM ) was first prepared in sterile MilliQ water.
Water was doubly distilled or obtained from a Millipore ( Billerica, MA ) MilliQ water purification system.
The total volume was adjusted to 10 µl with MilliQ water.
PCS-size analysis was carried out using filtered ( 0.2 µm ) MilliQ water as dispersing medium.
Cells were harvested by centrifugation and washed with 0.9 % NaCl in milliQ water.
Rinse twice with 50 ml of sterile MilliQ water.
One ml of this solution was taken and then placed in 100 ml of MilliQ water.
Cells were washed by resuspending with 25 mL sterile MilliQ water.
To do this, the oligonucleotides ON2 are deposited in MilliQ water.
You'll also be interested in:
Examples of using Water
Show more
There is no water damage or fire extinguisher residue
Do not clean the engine with water
Water freezing in the system will break it
