Examples of 'ml of water is added' in a sentence
Meaning of "ml of water is added"
ml of water is added: Refers to the action of including a specific volume of water, usually in milliliters, to another substance or mixture
How to use "ml of water is added" in a sentence
Basic
Advanced
ml of water is added
Ml of water is added to this solution.
Then a solution of 5 ml of concentrated sulphuric acid in 80 ml of water is added.
Ml of water is added to the mixture which is then extracted with methylene chloride.
After concentration to dryness, 10 ml of water is added to the residue is obtained.
The plates are constantly stirred for 10 minutes then 1 mL of water is added.
Then 90 mL of water is added to precipitate more solid.
Stirring is continued for a further 2 hours then 2 mL of water is added.
While stirring vigorously, 80 ml of water is added to the suspension formed.
The residue obtained is dissolved in pyridine ( 7 ml ), 3 ml of water is added.
About 70 ml of water is added by spraying over about a five minute period.
The reaction mixture is filtered and 60 mL of water is added to the filtrate.
An additional 200 mL of water is added during this process to facilitate stirring.
The THF is removed in vacuo and 10 ml of water is added.
And 1 ml of water is added.
The solvent is removed in vacuo and 100 mL of water is added.
See also
To the obtained powder, 20 ml of water is added and the mixture is stirred.
After cooling down to room temperature, 300 mL of water is added.
Under cooling with ice, 50 ml of water is added to the resulting reaction mixture.
After stirring for 8 hours a solution of 2,2 g of calcium chloride in 10 ml of water is added.
Approximately 10 mL of water is added and the mixture is stirred for two hours.
Subsequently DMF is evaporated and 20 ml of water is added to the residue.
Fifteen mL of water is added while maintaining the temperature near 78°C.
The resultant solution is cooled and 350 ml of water is added thereto followed by filtration.
While stirring vigorously, a solution of 55 g of potassium tartrate in 200 ml of water is added.
To this solution, 120 ml of water is added to dissolve sodium chloride for layer separation.
The resulting mixture is stirred rapidly for 20 minutes then 10 ml of water is added.
About 0.5 ml of water is added to the reaction mixture.
A mixture of 51 mL of acetone and 2.9 mL of water is added to the concentrate.
Finally, 20 mL of water is added and the mixture stirred again.
A solution of 900 mg sodium nitrite in 2 ml of water is added dropwise thereto.
About 3-5 ml of water is added to this solution.
A solution of 50 g of anhydrous dextrose in 250 ml of water is added to the former solution.
About 500 ml of water is added to the paste and blended well.
After the deprotection is completed 500 ml of methylene chloride and 300 ml of water is added.
Dissolved in 0.1 mL of water is added to the solution.
The reaction medium is transferred into a 2-L Erlenmeyer flask, then 900 mL of water is added.
Then, 200 ml of water is added and the mixture is hydrolyzed by boiling for 6 hours.
After warming to room temperature, 100 ml of water is added and the mixture acidified.
Afterwards, the catalyst is filtered off through Celite and 100 ml of water is added.
Twenty-five mL of water is added while maintaining the temperature near 78°C.
The reaction mixture is cooled to 60 °C and 30 ml of water is added very slowly.
You'll also be interested in:
Examples of using Water
Show more
There is no water damage or fire extinguisher residue
Do not clean the engine with water
Water freezing in the system will break it
Examples of using Added
Show more
I added some extra layers for fullness
New reports will be added as they are published
He added a number of other minor editorial changes
Examples of using Ml
Show more
One ml of saliva carries more germs than
Your doctor will prescribe the dose in ml
Six to eight ml of hydrogen peroxide will be necessary
