Examples of 'mm in thickness' in a sentence
Meaning of "mm in thickness"
The phrase 'mm in thickness' is used to indicate the thickness of an object or material, typically measured in millimeters. This measurement provides a specific indication of how thick something is, allowing for precise comparisons or descriptions of size and dimensions
How to use "mm in thickness" in a sentence
Basic
Advanced
mm in thickness
Mm in thickness when using the cutting disc supplied with this tool.
A press sheet of 2 mm in thickness was used as a test piece.
The mesh material is typically about 1 mm in thickness.
A brass plate of 5 mm in thickness was used as a hot plate.
The wall of said electrode has 1 mm in thickness.
Layers of up to 5 mm in thickness can be deposited without difficulty using thermal spraying.
In the restricted section it shall not exceed 4 mm in thickness.
A pipe of 8 mm external diameter and 1 mm in thickness was manufactured by coextrusion.
Use the insulation of polyethylene foam minimum of 5 mm in thickness.
Parallelepipedal silicone gasket 1 mm in thickness is applied between two test strips.
The extractor shell was locally affected by corrosion up to 2 mm in thickness.
Austenitic stainless steel strip 3 mm in thickness was cast between rolls.
The seeds are then covered with a layer of soil approximately 3 mm in thickness.
The glass employed is 5 mm in thickness and is degreased with acetone before bonding.
The metal substrate consists of a steel plate 1 mm in thickness.
See also
Only tumors less than about 5 mm in thickness may be treated by surface irradiation.
These preferred films generally do not exceed 1 mm in thickness.
A marbled sheet 2 mm in thickness is then obtained, which is conveyed towards the cutting system.
The tensile test pieces were 2 mm in thickness.
Layers of up to about 0.1 mm in thickness can be conveniently provided by electroplating.
The resulting sandwich structure was 1 mm in thickness.
Molding, rolling to 2 mm in thickness followed by rapping.
The inner pipe thus obtained was about 6 mm in thickness.
Up to 3 mm in thickness.
The material was processed for light microscopy and sections of 1 mm in thickness were st.
A layer of cardboard 2-3 mm in thickness has proved satisfactory.
The walls of a cavity are usually irregularly outlined and measure over 1 mm in thickness.
As an example, a sheet of 1.2 mm in thickness has the following composition,.
After treatment, the seeds are covered with a layer of soil approximately 3 mm in thickness.
As an example a sheet of 1.2 mm in thickness having the following composition,.
Example 1 describes the production of an ultrafiltration membrane on porous metal discs 2 mm in thickness.
An aromatic polycarbonate polarizing sheet 0.6 mm in thickness was obtained as a result.
Wood simply sawn lengthwise or produced by a profile-chipping process; normally exceeds 6 mm in thickness.
The expanded extruded strip obtained is 4 mm in thickness and 55 mm in width.
In particular, it is a stamped galvanized-steel or aluminum plate approximately 0.1 to 2 mm in thickness.
Optional melamine top, 25 mm or 30 mm in thickness depending on the furniture range.
The normal appendix is rarely seen, with a wall of no more than 6 mm in thickness.
Optional melamine top, 25 mm or 30 mm in thickness according to the desk range.
The index I c used hereafter is calculated for a glass 4 mm in thickness.
Blocks of tissue 2 mm in thickness were cut in 0-4 °C sucrose solution using a vibratome.
This is a pressboard up to 8 mm in thickness.
The tape with 1.7 mm in thickness is then crosslinked at a temperature of 90°C in a waterbath.
After drying the rubber, sheets of polymer around 2 mm in thickness were prepared.
A composite film 2 mm in thickness is thus produced by means of a hydraulic press heated to 110 ° C.
The obtained mixture was rolled thrice and then a sheet of 3 mm in thickness was prepared.
More than 5 but not more than 10 mm in thickness More than 10 mm in thickness.
The cartilaginous coating tends to vary from 1 to 3 mm in thickness.
The resulting tablets measured 9 mm in diameter by 1 mm in thickness and weighed 0.10 gm each.
The circular medal measures 34 mm in diameter and 3 mm in thickness.
A disc like rotor 35 mm in diameter and 12 mm in thickness is used for this purpose.
You'll also be interested in:
Examples of using Mm
Show more
Mm vinyl coated steel retracting security cable
Is the nominal diameter of the rim expressed in mm
Mm small brush with black polyester bristles
Examples of using Thickness
Show more
Minimum recommended thickness of zinc vs thickness of steel
Thickness of tanks made with double walls
Reduction of wall thickness and additional protection
