Examples of 'moulding operation' in a sentence
Meaning of "moulding operation"
moulding operation: This phrase typically refers to a process or a facility where molding or shaping of materials, such as plastics or metals, takes place
How to use "moulding operation" in a sentence
Basic
Advanced
moulding operation
The housing is conveniently produced by a moulding operation.
The injection moulding operation is then carried out.
It can furthermore be mass produced by a single moulding operation.
The moulding operation was repeated many times and no adhesion phenomena could be observed.
This shaping is carried out by the moulding operation itself.
The injection moulding operation and head office is located in Montréal.
These elements may be formed in a single injection moulding operation.
This adds to the cycle time of the moulding operation and makes it relatively inefficient.
Thus the shell would be obtained by a single moulding operation.
Preferably, the moulding operation comprises a blowing operation and a welding operation.
Through an initial moulding operation.
Preferably, the moulding operation of the mass of resin is carried out under vacuum.
The appliance is injection moulded in a two step moulding operation.
In addition, after the moulding operation the sealing can be pressurized / adjusted to a desired pressure reading.
Tuesday afternoon a slide breaks during the injection moulding operation.
See also
Separately, the moulding operation described above with reference to Figure 6 is carried out.
The lattice no longer has to be shaped independently of the moulding operation.
The initial part of the moulding operation produces the structure shown in Figures 2 and 3.
This connector has the disadvantage of requiring an additional moulding operation.
In this case, too, the moulding operation was repeated many times, using the same plates.
The preform thus heated is ready for the blow moulding operation.
The cover 18 is moulded in a cover moulding operation 104 using a conventional technique.
The trainer is made of silicone rubber and is moulded in a single moulding operation.
These manipulation problems make the biscuit moulding operation particularly difficult.
Regarding the frame 3, it is preferably made of a plastic material through an injection moulding operation.
A pedal according to claim 15, characterised in that the moulding operation is an injection-moulding operation.
The sealing and guiding strip 24 is manufactured in a single integral piece by a single moulding operation.
Yet further the trainer can be manufactured in a moulding operation in large quantities.
The radial projections may also receive and support terminal posts during a moulding operation.
These lateral walls 3 appear during the moulding operation.
A bottle body 2 has a mouth 4 which is integrally formed in a single blow moulding operation.
FIG . 2 is a view of the master before the moulding operation.
In such processes, resin and reinforcement are combined and cured in the same moulding operation.
FIG . 1 shows the pressure v. time curves during a moulding operation and.
Thus, the necessary sharp corners at A, B and C are easily produced by the moulding operation.
The end wall to the collar can be applied as a post moulding operation.
The head and the spine may be made in the same moulding operation.
Specifically, a cover is formed over the neck during the moulding operation.
The pedal is of one-piece construction and produced by a single moulding operation.
Thus, the head, including the closure, is produced in a single moulding operation.
Incidentally, the blank 4 is made beforehand, for example by means of a moulding operation.
As stated above, the sealing and guiding strip 24 is manufactured by a moulding operation.
Naturally, inserts 22 can be anchored in flange 18 thus formed, during a single moulding operation.
The upper wall 21 of the sheet path is moulded in an injection moulding operation 106.
Alternatively, the whole ball 26 including the core 27 may be formed in a single moulding operation.
You'll also be interested in:
Examples of using Operation
Show more
We ran a good operation and said nothing
Operation with wire cup brush accessory
It has been in operation for only a few months
Examples of using Moulding
Show more
Rotational moulding large volume hollow bodies
Comprehensive management for injection moulding technology
Inner deck moulding for easy maintenance
