Examples of 'output of the amplifier' in a sentence
Meaning of "output of the amplifier"
output of the amplifier: the sound or signal produced by an amplifier; typically refers to the audio produced by a device designed to increase the amplitude of a signal
How to use "output of the amplifier" in a sentence
Basic
Advanced
output of the amplifier
Adjust the sound output of the amplifier.
The output of the amplifier was measured on a streak camera and a monochromator.
Selects the power output of the amplifier.
The output of the amplifier is usually terminated by the radio frequency transformer.
This limits the peak voltage output of the amplifier.
Connect the output of the amplifier to your house distribution.
Some fault conditions may cause the output of the amplifier to be muted.
The output of the amplifier circuit is used to control an accommodative IOL.
It therefore enables a measurement of the distortions of modulation appearing at output of the amplifier.
For adjusting the output of the amplifier to the input of the source unit.
The positive input of each comparator is connected to the output of the amplifier.
This circuit protects the output of the amplifier against DC voltage.
It is desirable to work with constant output amplitude at the output of the amplifier.
A differential output of the amplifier AOPG constitutes an output of the gain control loop.
The handling capacity of the loudspeakers is adequate for the output of the amplifier.
See also
The output of the amplifier AEM is connected to the terminal SEM.
These two components use different paths to reach the output of the amplifier.
Connect the other output of the amplifier to the Full Range cabinets.
A signal having a larger amplitude may thus be supplied from the output of the amplifier.
The input and the output of the amplifier are respectively referenced E and S.
The capacitor is connected between the first input and the output of the amplifier.
The constant amplitude obtained at the output of the amplifier 33 is divided into two channels.
There is a section 12 i of dispersion compensating fiber at the output of the amplifier.
The output of the amplifier OP-AMP is inherited to lower stages.
MASTER knob adjusts the overall output of the amplifier.
Connect each output of the amplifier LEFT / RIGHT to each cabinet using two wires, independently.
The output of this filter is connected to the output of the amplifier PA.
The output of the amplifier AO 3 is connected to the output O 1 of the secondary part.
Remapping the spread spectrum composite signal at the output of the amplifier system ;.
The output of the amplifier OA2 is therefore positive due to which transistor P9 is blocked.
The processor means comprise integrator means connected to the output of the amplifier stage ;.
The output of the amplifier COMP is looped onto the second input, via an impedance Z ′.
A second resistor 91 is linked between this negative input and the output of the amplifier.
The output of the amplifier 31 is connected to the processor.
Finally, a capacitor is parallel-connected to this first input and the output of the amplifier.
The output of the amplifier is linked to a demodulation circuit 38.
A capacitor is planned, connected between the positive input and the output of the amplifier.
The output of the amplifier is applied to a transmitting antenna 22.
The calibration circuit 50 functions as a calibration means to adjust the output of the amplifier circuit.
At the output of the amplifier is a dispersion compensating fiber section 12 i.
MASTER volume control, adjusts the total power output of the amplifier.
At the output of the amplifier is a section 12 i of dispersion-compensating fiber.
It is the collector of T1 which constitutes the output of the amplifier in this case.
The output of the amplifier 63 is connected to its inverting input.
Its inverting input is also connected to the output of the amplifier 6 by a resistance R7.
The output of the amplifier 78 therefore remains at ground potential.
With a filtered signal the constellation at the output of the amplifier is represented in FIG . 3A.
The output of the amplifier 5 is connected to an amplitude detector or sensor 6.
The amplifier system A1 has an output 0 which is the output of the amplifier arrangement.
The speaker output of the amplifier were connected to a 100 ohm dummy load.
You'll also be interested in:
Examples of using Amplifier
Show more
Make sure that the amplifier is switched on
Amplifier is picking up alternator noise or radiated noise
Never operate the amplifier without cover
Examples of using Output
Show more
One output will contribute to this outcome
Illuminates when output is sent to the tray
Output signals common to measuring technology are available
