Examples of 'peel adhesion' in a sentence
Meaning of "peel adhesion"
The measure of the force required to peel an adhesive material off a substrate under specified conditions
How to use "peel adhesion" in a sentence
Basic
Advanced
peel adhesion
Peel adhesion is provided in the table below.
This is a modification of the standard peel adhesion measurement.
Peel adhesion reaches the maximum at the transition speed.
Another routinely performed test measures peel adhesion.
Peel adhesion was then measured on all three test substrates.
It is generally indicative of the final peel adhesion of practical underlays.
The peel adhesion values were determined according to the following procedure.
Tests have shown that the peel adhesion almost doubles.
As stated above the adhesive bond possesses excellent peel adhesion.
Peel adhesion to a conventional general purpose rubber carcass stock was also measured.
The coated samples were tested for peel adhesion and shear strength.
Testing the peel adhesion of different polysulfide sealants with a comparative fatigue method.
The most preferred CMTg values provided preferred levels of peel adhesion.
The peel adhesion is dependent on the aqueous adhesive composition and the substrate.
The painted test substrates are the same as those described in the peel adhesion test.
See also
Peel adhesion was then measured for samples for all three test substrates.
The adhesives properties of the obtained protective films demonstrate the precise control of peel adhesion.
The maximum peel adhesion value and failure mode were noted and recorded.
The samples are then tested according to the Peel Adhesion Test Method.
The peel adhesion is the force required to remove the protective film from a test panel.
Table IV shows a comparison of peel adhesion properties at elevated temperatures.
Peel adhesion data is set forth in Table II.
Test results for immediate peel adhesion to a glass surface are given in Table III.
The peel force is measured according to the Peel Adhesion Test Method.
The ultimately desirable peel adhesion will depend on the intended use for the adhesive.
Only crosslinked samples were evaluated for density, peel adhesion and tensile / elongation.
The following peel adhesion tests on fabric were carried out,.
Table 2 also shows a qualitative analysis of the peel adhesion failure mechanism observed.
Rather, the peel adhesion will increase upon ageing.
The block copolymer provides flexibility, integrity and smooth peel adhesion properties.
In some cases, the peel adhesion was too high.
The peel adhesion strength test is conducted using a tensile testing machine as follows,.
At low speeds, the peel is smooth and peel adhesion increases with increasing speed.
Peel adhesion is one method of determining the adhesive strength of a pressure-sensitive tape.
However, anisotropic shear strength can occur without the occurrence of a corresponding anisotropic peel adhesion.
Specimens for peel adhesion testing were prepared in accordance with the following formulae,.
These values are used as benchmarks for the semi-quantitative peel adhesion test described below.
The peel adhesion is measured 30 minutes after application of the adhesive to the test plate.
An adhesive composition containing less than 5 pbw will not have a stable peel adhesion strength.
In the peel adhesion test, failure during testing occurred at the interfaz of the seam.
Such adhesives exhibit aggressive tack but low peel adhesion properties, thus allowing repeated reuseability.
The peel adhesion enhancement is most pronounced for the examples containing ethylene vinyl-acetate copolymers.
Upon removal after a substantial residence time, the low initial peel adhesion surface will regenerate.
Tensile strength, percent elongation, and peel adhesion strength properties of the pressure-sensitive adhesives were measured.
When more PIB is added to the system, the peel adhesion decreases.
The peel adhesion values obtained are summarized in the following Table 2.
The tapes were tested again for their peel adhesion after aging at RT for 4 weeks.
The maximum peel adhesion value was recorded in Newtons per decimeter, as indicated above.
Some of the articles of the examples were tested for 90 ° peel adhesion.
Data from the peel adhesion study for the various terpolymer compositions is reported in Table 2.
You'll also be interested in:
Examples of using Adhesion
Show more
Test for adhesion performance on wet surfaces
Transition from high to low adhesion surfaces
Very high adhesion and quick drying
Examples of using Peel
Show more
Do not peel the fruit before drying
And then he will want me to peel a banana
Peel the onions and dice them
