Examples of 'polymer content' in a sentence
Meaning of "polymer content"
This phrase refers to the amount or proportion of polymer material present in a substance or product. It is commonly used in the context of manufacturing, chemistry, or material science, to describe the composition or quality of polymers
How to use "polymer content" in a sentence
Basic
Advanced
polymer content
High polymer content hybrid drag reducers.
No mention is made of the percentage of polymer content.
The polymer content in the filtrate is gravimetrically determined.
Bituminous mixtures with a high polymer content.
Their polymer content may be variable according to their origin.
Information on the low molecular weight polymer content.
The polymer content in the solution influences its viscosity.
This is connected with a high polymer content of the granulate.
The polymer content in the preparation was determined by gel chromatography.
Gel elasticity increased with polymer content and calcium concentration.
The polymer content in the water is of the order of one percent.
Small aliquots are removed periodically and analyzed for polymer content.
No correlation between polymer content and tensile properties could be seen.
A sample of the admixture is taken and analyzed for polymer content.
The polymer content may be greater than in the fibre coating solution.
See also
These samples are analyzed for polymer content vÃa the methanol turbidity method.
The electrical resistivity p is measured in order to check the reduction in polymer content.
The living polymer content also corresponds to the content of functional chains.
They still have to be improved in order to increase the specific polymer content.
Thus the polymer content in the albumin preparation of the present invention was extremely low.
The enthalpy associated with these transitions decreased as polymer content decreased.
The polymer content is determined by the thus resulting GPC chart as exemplified in Fig.
Does not teach how to make adhesives with very low polymer content.
The polymer content is determined to be about 6 percent.
The compression strength of the foamed article does reduce with increasing acrylic polymer content.
Flexibility in adjusting the polymer content of the reconstituted dispersions, and.
Accordingly, there is an optimum range for the polymer content.
To get a soft material, the polymer content should be as low as possible.
The polymer content was calculated as the % ratio of polymer weight to the gel weight.
Tensile properties are strongly dependent on the crystalline SPC polymer content in the formulation.
Next, the polymer content in the solution will be described below.
EXAMPLES The coatings are described based on the polymer content of the coating.
Strains were grown and polymer content was analyzed in the same manner described in example 1.
Hughes et al . does not teach how to make adhesives with very low polymer content.
The balance of the polymer content is substantially based upon units derived from butene-1.
In general, lamination temperatures will depend on the specific polymer content of the layers.
Stable bitumen-polymer mixtures of high polymer content are preferably prepared by the following procedure.
The polymer content of the hydrophilic layer may be described also by a weight / volume percent.
More specifically, it relates to concentrated binders for bitumen / polymers with very high polymer content.
Intracellular polymer content was analyzed by butanolysis as in Example 1.
EXAMPLE 1 Mixtures of high polymer content.
The minimum polymer content in the composition should be 20 % by weight.
It is expected that dispersions with up to 30 % active polymer content may be prepared.
The polymer content of this polymer / asphalt admixture was again 3 %.
All quantities concerning the claimed material are related to a total of 100phr of polymer content.
The minimum polybutylene polymer content in the composition should be 15 %.
The polymer content in the solution of the treating agent is preferably 2 to 70 % by weight.
Samples ( 5 g ) were withdrawn at different intervals of time and the galactosyl polymer content was determined.
The polymer content for all formulations was 10 % by weight in the adhesive.
The material according to claim 1-4 wherein the polymer content of the polymer blend is elastomeric.
You'll also be interested in:
Examples of using Content
Show more
On the product content and environmental release
Content management interfaces for web systems
Adjusts style and content when necessary
Examples of using Polymer
Show more
Injected polymer compound shell in three sizes
We seem to be a bit light in the polymer sciences
High resistance polymer flow indicator cover
