Examples of 'polymerisation conditions' in a sentence
Meaning of "polymerisation conditions"
polymerisation conditions - These are specific factors or variables that influence the process of polymerization, which is a chemical reaction where monomers are combined to form polymers. Polymerization conditions can include temperature, pressure, catalysts, and other factors
How to use "polymerisation conditions" in a sentence
Basic
Advanced
polymerisation conditions
The polymerisation conditions are detailed in the corresponding examples.
This introduction is possible whatever the polymerisation conditions.
The polymerisation conditions are presented in the following table.
The monomer distribution is determined by the polymerisation conditions.
Typical polymerisation conditions are presented in the examples below.
The alkane is particularly effective under polymerisation conditions of low comonomer concentrations.
Polymerisation conditions are controlled on both reactors to ensure suitable product properties.
The first reactor can be used or not used depending on the polymerisation conditions.
The other grafting polymerisation conditions will follow the usual procedure for such process.
Both amorphous or ordered systems can be prepared depending upon the particular polymerisation conditions used.
The polymerisation conditions used are summarised in the Table below.
Both amorphous and ordered systems can be prepared depending upon the particular polymerisation conditions used.
The polymerisation conditions are set out in the following Table.
Nitrogen was used to obtain oxygen-free polymerisation conditions.
The polymerisation conditions are summarised in Table II.
See also
The monomer ( s ) are generally polymerised under free radical polymerisation conditions.
The polymerisation conditions and results are displayed in Tables III to VIII.
The inert diluent may be any hydrocarbon, which is not reactive in polymerisation conditions.
At polymerisation conditions in a polymerisation zone, to produce a polymer.
In these processes the polymerisation conditions can be batch, continuous or semi-continuous.
Polymerisation conditions are shown in table 1.
The catalyst component combinations, polymerisation conditions and polymer properties are summarised in Tables I and II.
Polymerisation conditions are given in Table 1.
The result indicated that, under the polymerisation conditions used, neodymium " versatate " gave superior results.
Polymerisation conditions and product characteristics are shown in Table 2 and 4.
Table 2 contains the polymerisation conditions specific to Example 1.
The polymerisation conditions were otherwise identical to example 1.
Maintaining under first polymerisation conditions to produce a first high molecular weight polyolefin component ;.
The polymerisation conditions are indicated in table 1.
The detailed polymerisation conditions are specified in Table 2.
The polymerisation conditions were as follows,.
Table 1 summarizes the polymerisation conditions and polymer characteristics of the preceding Examples.
The polymerisation conditions in the gas phase reactors were as follows,.
The other polymerisation conditions are specified in Table 2.
The polymerisation conditions and polymer properties are given in table 2 below.
These homogeneous polymerisation conditions in DMSO gave the polymer 1 in a matter of minutes e . g.
The polymerisation conditions are generally as described above for epoxide-functional monomers.
TABLE 1 polymerisation conditions.
The polymerisation conditions and the characteristics of the copolymer thus obtained appear in Table 1.
The polymerisation conditions applied are listed in Table 1.
The polymerisation conditions appear in Table 1 below.
The polymerisation conditions therein are given in Table 2.
The polymerisation conditions are shown in Table 1 below.
The polymerisation conditions are shown in Table 2 above.
The polymerisation conditions are presented in Table 7.
The polymerisation conditions and feeds are listed in Table 1.
The polymerisation conditions and the product properties are shown in Table 3.
The other polymerisation conditions and copolymer properties are specified in Table 1.
The polymerisation conditions and results are summarised in the following tables . Figs.
The polymerisation conditions and product recovery method used were the same as in Example 11.
You'll also be interested in:
Examples of using Conditions
Show more
There are no conditions or costs attached to this service
This sector is characterised by poor working conditions
Conditions and modalities for reimbursement or payment
Examples of using Polymerisation
Show more
Fenbendazole inhibits the polymerisation of tubulin to microtubules
Polymerisation is carried out in the presence of catalyst
Only to be used in the polymerisation of fluoropolymers when
