Examples of 'pulse is applied' in a sentence
Meaning of "pulse is applied"
pulse is applied - This phrase refers to the act of administering a series of rhythmic electrical or mechanical impulses, commonly used in medical contexts such as CPR or physical therapy
How to use "pulse is applied" in a sentence
Basic
Advanced
pulse is applied
This pulse is applied to the output stage.
Both sets of transitions show a step increase in intensity as the voltage pulse is applied.
The modulated pulse is applied to a charge pump arrangement.
In TENS type apparatuses a unipolar or bipolar pulse is applied to the target área.
This pulse is applied to the electrode pair whose impedance is to be measured.
This beginning of the pulse is applied to the input IGN.
No pulse is applied during this phase to the input terminal TL.
Subsequently, a machining pulse is applied.
A voltage pulse is applied between the electrodes to create the electric field.
In accordance with step a, a current pulse is applied to the present sensor element.
A voltage pulse is applied to the Pockels cell to control resonator loss.
Furthermore, an anodic pulse equal to a tenth of charge pulse is applied during the pauses.
In the prior proposal a pulse is applied to the control region through the capacitor Cox.
In this manner, preventing surge when the electric pulse is applied would be achieved.
When a sharp pulse is applied to the shaft, the spring expands.
See also
After a time, the symbolic point is at B and the second pulse is applied.
An electrical pulse is applied across the electrodes, heating the gas into a plasma.
At the instant t2, the resetting pulse is applied.
A painless laser pulse is applied to the surface of the skin through a wristwatch-style device.
At the instant t3, the remanence erasure pulse is applied.
In this method, a second voltage pulse is applied across the electrodes after the predetermined time.
Point 24 is the point of needle 11 where a mechanical excitation pulse is applied in a real experiment.
An EP pulse is applied according to the following treatment parameters,.
In addition a positively directed field blanking pulse is applied to detector 1 for activating the detector.
When a pulse is applied to a selection line Li, the switching transistor T is turned on.
The current-controlled or constant current pulse is applied at step 52.
The low-frequency pulse is applied by a means of excitation chosen from,.
To switch off transistor Tp, a negative pulse is applied to winding W2.
A voltage pulse is applied to the piezoelectric device ( 83 ) to generate distortion stress.
To control this switch, a positive pulse is applied to the control terminal 41.
An RF pulse is applied to rotate magnetization by 90 degrees.
In a step S 3, one erase or program pulse is applied to designated memory cells.
This pulse is applied vía the start control circuit 24 to the input SI.
At block 32, an electrical signal pulse is applied.
During Q-switching, a voltage pulse is applied to decrease loss in the resonator.
This pulse is applied to the input CK of counter 32 via synchronization AND gate 34.
Typically, a 4 V voltage pulse is applied in the reverse direction.
Thus, a pulse is applied to the input of IC2.
When selecting a ( video ) line, a positive voltage pulse is applied to the relevant selection electrode ( 9 ).
This pulse is applied to a start input 39 to start a counter 40.
For actuation of the device a high current pulse is applied to the connection lugs ( 326 ).
The pulse is applied at the first sensing element 216.
In addition, at instant t0, a pulse is applied to the reset input of the microprocessor.
Such a pulse is applied at time t1 to transistor T1, with transistor T2 not conducting.
More precisely, an electrical pulse is applied to the electrical poles of the first coil 16.
A single tickle pulse is applied at the lead 32, initiating power application to the heater element 10.
At time t=0, a current pulse is applied to the electrical cutting element to generate heat.
Whenever a trigger pulse is applied to the input, the 555 will generate its single-duration output pulse.
When a positive pulse is applied to the gate 20, current flows in the transistor T3, thus formed.
This gate pulse is applied to the AND gate 39 through the OR gate 55.
You'll also be interested in:
Examples of using Pulse
Show more
The pulse only lasts a couple of microseconds
I can not get a pulse on the doppler
His pulse and respiration are below normal
Examples of using Applied
Show more
One caveat must be applied to this analysis
We applied three event history analysis methods
It may also be contested as applied in a certain investigation
