Examples of 'resistivities' in a sentence
Meaning of "resistivities"
resistivity (noun): 'resistivity' is a property of a material determining its resistance to the flow of electric current, often measured in ohm-meters and used in various fields of physics and engineering
Show more definitions
- plural of resistivity
How to use "resistivities" in a sentence
Basic
Advanced
resistivities
Materials with low resistivities are good conductors.
Plastics generally have very high resistivities.
However resistivities that are too low or too high are both undesirable.
Thicker plates would use lower resistivities.
The results show apparent resistivities measured for seven depths of investigation levels.
They have the advantage of having relatively high resistivities.
The following table shows the resistivities of several materials.
The individual resistances are dependent on the geometric dimensions and the resistivities.
The corresponding specific contact resistivities are thus extracted.
The electrical resistivities of said wall are measured using electrodes on each of said pads.
Thickness dependent sample resistivities are observed.
Such a material therefore exhibits at least two stable resistive states having different resistivities.
Carbonaceous or organic aerogels have electrical resistivities which are perfectly suitable in this respect.
The electrical resistance of normal glass microelectrodes was calibrated against surrounding solutions of different resistivities.
Relative depth varies with temperature because the resistivities and permeability vary with temperature.
See also
The following table shows calculated temperature rises for products with various resistivities.
Good electrical conductors have very low resistivities and good insulators have very high resistivities.
This may be provided by a heating element comprising different materials having different electrical resistivities.
The susceptor should also have relatively low electrical resistivities to increase Joule heat dissipation.
Modifications of the general method described herein will also result in low contact resistivities.
The weighted values of the contact resistivities are shown in Table V.
The line resistivities increase, after annealing.
Excellent Homogeneity at high emitter resistivities.
On average, electrical resistivities tend to increase inland.
In addition we have also calculated the ideal thermal resistivities of K and Rb.
Thereafter, the resistivities of the liquid crystal layers were measured.
Since these parts are superposed, their resistivities combine additively.
Resistivities of these polymer films are three-dimensionally isotropic and tend to be relatively high.
Rocks can be altered and therefore can show lower resistivities ( in yellow or orange ).
The resistivities measured from the wafer surface above non-implanted areas are compared.
As for the thus obtained electric resistivity, the electric resistivities of all 5 samples are obtained.
Silver pastes have resistivities which can, of course, vary according to their silver concentration.
Driver transistors are characterized in terms of drift-region implant dose, design parameters, and substrate resistivities.
Thus, the measurement represents a value which integrates the resistivities over a certain volume of the subsoil.
In most common geological environments, the best water-yielding zones have the highest resistivities.
The surface resistivities are of the same order of magnitude as in Example 2.
In some cases, the particulate material may comprise a mixture of materials having differing volume resistivities.
The resistivities calculated from the results plotted in Figure 34 are as follows.
The voltages, currents, and DC resistivities were read using digital multimeters.
Table I describes the various UTTFs, sheet resistances and resistivities thereof.
The reduced samples had surface resistivities on the order of several hundred Ω / . quadrature.
Furthermore, these CER and TLTR devices are only suitable for measuring horizontal interface resistivities.
TABLE IV . Surface resistivities of pilot laminates glued by a mixture of polyvinyl alcohol and polyaniline.
Substrate wafers prepared from these undoped crystals exhibit resistivities of up to 105 ohm-centimeters.
Typical resistivities are below 1 milliohm·centimeter.
All the carbonized materials had electrical resistivities of less than 1 Ω . m.
The resistivities obtained are given in Table 3 below,.
The ITZO ceramics demonstrate electrical resistivities that are lower compared with that of ITO ( FIG . 9 ).
Higher resistivities are suitable for devices powered at voltages greater than 240 volts AC.
This result is interpreted using a layer model to approximate two surface layers with resistivities? s = 108?
