Examples of 'signal attenuation' in a sentence
Meaning of "signal attenuation"
Signal attenuation refers to the reduction in the strength or intensity of a signal as it travels through a medium, such as a cable or wireless transmission. It is commonly used in telecommunications and networking to describe the loss of signal power over distance
How to use "signal attenuation" in a sentence
Basic
Advanced
signal attenuation
This signal attenuation can be quite considerable.
The frequency region in which there is little signal attenuation.
Minimal signal attenuation allowing use in deep boreholes.
This technique is much more robust against signal attenuation.
Signal attenuation may be assessed in any appropriate manner.
Shannon developed a formula to quantify signal attenuation in early telephone lines.
Set the signal attenuation for all input channels.
Optical fiber amplifiers are usually provided to compensate for signal attenuation.
Common mode signal attenuation for a differential duplexer.
The maximum length of the bus cable is limited by signal attenuation.
The signal attenuation model.
It varies depending on the surroundings and factors that cause signal attenuation.
Signal attenuation is particularly problematic in central cavity cable designs.
It compensates for the additional signal attenuation caused by the foam surfaces.
The signal attenuation along the acoustic path is reduced.
See also
The spreading of the fiber by the rotating deflector mitigates signal attenuation.
Set the signal attenuation for the two input channels.
This has placed greater emphasis on high signal attenuation by the shielding medium.
Signal attenuation apparatus.
One way to obtain higher signal quality in communication cable is to lower signal attenuation.
No signal attenuation.
Longer distances and higher frequencies using this method meant more signal attenuation.
Total signal attenuation was observed with longer probes in clogged peat soils.
The choice will be a compromise between heat load to the cold space and signal attenuation.
Overall signal attenuation is used to determine a mass flow rate for higher application rates.
Determines the time elapsed since the activation of the PAGE key until signal attenuation starts.
The signal attenuation is not due to NMR resonance saturation.
Several reasons may explain the BOLD signal attenuation.
Very low signal attenuation less than 1 dB.
These factors all cause severe Wi-Fi signal attenuation.
For signal attenuation from dry materials, see table below.
Dielectric signal loss is reduced significantly, reducing signal attenuation.
Most providers rely on signal attenuation along with trilateration to compute one 's position.
These indices are power measurements or received signal attenuation estimates, for example.
Thus, using signal attenuation for canola will likely not work well.
In contrast, the terms a n and a m for signal attenuation are much more pertinent.
In addition, it is possible to obtain good concentricity without significantly increasing signal attenuation.
Calculating a value of a signal attenuation for the subscriber line from the one-ended measurements ;.
However, they are not very rigid and introduce substantial signal attenuation.
The different curves show signal attenuation in the individual fibres 2 of the cable of Figure 1B.
The third signal attenuator unit is arranged to apply 1dB of signal attenuation.
Signal attenuation degraded 60 GHz radar results at long distances.
In particular, a high gain directional antenna may compensate for signal attenuation in a direction.
Signal attenuation may be assessed is any appropriate manner for purposes of step 376.
In particular, the composite may fade due to multipath or other signal attenuation mechanisms.
Compared with Fig . 3, signal attenuation is significantly reduced.
Temperature variations cause the cable to expand and contract, which leads to signal attenuation.
Technological challenges for FSO communications include, ( i ) signal attenuation due to atmospheric absorption or scattering.
The input signal strength is then used to calculate the peak-width deviation and signal attenuation.
This, in turn, decreases the signal attenuation in the glazing.
You'll also be interested in:
Examples of using Signal
Show more
Give me a signal when you want me to start
You have to use one signal at a time
Signal strength indicating connection between units
Examples of using Attenuation
Show more
This low attenuation may be explained by sharpfocusing
Means of simulating the attenuation of a test cable
Direct attenuation correction systems are commercially available
