Examples of 'styrene content' in a sentence
Meaning of "styrene content"
styrene content - the amount or percentage of styrene present in a material or substance
How to use "styrene content" in a sentence
Basic
Advanced
styrene content
The styrene content was calculated thereform.
Such dispersions are usually prepared in emulsion and are high in styrene content.
It is preferable to maintain the styrene content in this range to achieve optimum flexibility.
The copolymer obtained according to this process has a low styrene content.
Usually the styrene content tends to control the glass transition temperature.
This determine a modification of the glass transition temperature of the compound with higher styrene content.
Any styrene content within these ranges can be used with the present invention.
Recovering a product from said hydrogenation reactor having a reduced phenylacetylene content and an enhanced styrene content.
The low styrene content is added to control the VOC emissions.
In the styrene-butadiene copolymer rubber, the bound styrene content is not particularly limited.
The styrene content and the styrene block content are measured using proton NMR techniques.
Natural rubber latex compounds are modified by the addition of a high styrene content styrene-butadiene copolymer.
Styrene content of ES interpolymer in mole percent.
In the case of HSR, a high styrene content copolymer of butadiene and styrene is meant.
This definition applies to polymers having less than 50 % by weight of styrene content.
See also
Polymerized styrene content of polymer, mol percent.
This invention utilizes a radial styrene-butadiene-styrene block copolymer with a styrene content greater than 35 %.
The styrene content in the ethylene / styrene interpolymers is determined by NMR.
Thus, if a relatively low Tg SIBR is desired, a high styrene content is the primary consideration.
The styrene content refers to the proportion of styrene blocks included in the ( A ).
The ethylene-styrene interpolymer desirably has a styrene content of at least 60 percent by weight.
The low styrene content is added to minimize the problem with volatile organic emissions ( VOC ).
The obtained copolymer had a styrene content of 35 % by mass.
The styrene content is measured by Fourier transform infrared spectroscopy ( FTIR ).
When a styrene / butadiene copolymer is used, the styrene content customarily is below 20 % by weight.
The styrene content is determined in, for example, the following manner.
Suitable block copolymers of styrene and butadiene include those with a styrene content of about 10-50 wt %.
The styrene content of this styrene / butadiene copolymer is preferably less than 50 wt %.
The method of claim 7 wherein the styrene-butadiene copolymer has a styrene content below about 20 % by weight.
The residual styrene content of the polymer thus withdrawn was 150 ppm.
The elastomer-thermoplastic composition of Claim 2, wherein the rubber has a styrene content over 9 wt %.
If the styrene content is lower than 10 %, the erasability of the ink tends to deteriorate.
The SBS triblock copolymer has a nominal styrene content of 22.9 wt %, based upon total triblock weight.
If the styrene content is greater than 35 %, the inks may have an undesirably high viscosity.
Example 1 has approximately the same coupling efficiency ( load-bearing capacity ), and styrene content as Demonstration 5.
The fibers had a styrene content of 31 pph, based on the propylene polymer material.
The resultant copolymers were analyzed for 1,2-microstructure and for styrene content using Infrared Spectroscopy ( IR ).
In another embodiment the styrene content of the copolymer ranges from 25 to 45 percent by weight.
Styrene content ( % ) The styrene content was measured by IR spectroscopy using a calibration curve.
Further, the block styrene content was 0 % per total rubber.
Styrene content of copolymer ( percent by weight ) ;.
The copolymer should have a styrene content of 15 to 25 % by weight of the copolymer.
A styrene content from 20 to 75 weight percent based on total weight of polymer ; and.
Hydrogenation degree, styrene content and vinyl bond amount Values were calculated from 1H-NMR spectra.
The styrene content of the block copolymer is 5 to 50 % by weight.
Here, the styrene content is determined by 1H NMR.
The styrene content in unsaturated polyester resins is normally from 25 to 40 %.
The styrene content within this styrene-butadiene copolymer should be 50 wt % or less.
Also, the styrene content in the copolymer is not more than 10 % by mass.
I-2 Styrene content in the block copolymer.
You'll also be interested in:
Examples of using Content
Show more
On the product content and environmental release
Content management interfaces for web systems
Adjusts style and content when necessary
Examples of using Styrene
Show more
Polystyrene results when styrene monomers interconnect
The mass of polymerized styrene is practically quantitative
Styrene is made in large quantities by heating ethylbenzene
