Examples of 'total polymer' in a sentence
Meaning of "total polymer"
total polymer - the complete amount or sum of a compound consisting of multiple similar units bonded together
How to use "total polymer" in a sentence
Basic
Advanced
total polymer
Filler concentration is based on total polymer composition weight.
The percentage of the ethylenic polymer blended in the total polymer.
The water concentrations are relative to total polymer in the foamable thermoplastic polymer composition.
Many of the hydrogels described herein have an exceptionally low total polymer concentration.
The diluent was flashed off and the total polymer recovered was tested for various characteristics.
Type of resin employed The percentage of the EAA copolymer blended in the total polymer.
A total polymer yield of 42 g is obtained after evaporation of the volatile components.
The free and bounded polymer together comprised the total polymer present in the water system.
Decreasing the total polymer concentration also leads to softer gels at a given PVP-chitosan ratio.
In a typical prepolymerization less than about 5 % wt of the total polymer is produced.
By total polymer is meant polyurethane A, vinyl polymer B and other polymers present.
Results are given in parts per million ( ppm ) by weight on the total polymer product.
At least 5 % by weight of total polymer of an oxygen containing ethylene copolymer ;.
The adhesion barrier has a density of about 5 grams total polymer per square foot.
The total polymer solids in the preformed stabilizer is 5.4 weight percent.
See also
Hydration, shear and ionization degrade the total polymer and disrupt the mass structure.
The ES interpolymer contains approximately 4 % amorphous polystyrene in the total polymer.
The total polymer concentration of the membrane dope solution is preferably 25 % or higher.
HI value is given in wt % with respect to the total polymer.
The total polymer residence time through the disk processor was about 45 seconds.
Isothiazolone is added to a total amount of 30 ppm AI based on total polymer emulsion.
Up to 20 % wt of the total polymer content of the layer.
The amount of comonomer usually does not exceed 10 mol % of the total polymer.
Weight-percent or more filler based on total polymer composition weight ; and.
Total polymer solids of the tagged polyDADMAC was measured at 15 %.
Weight-percent or more of a filler based on total polymer composition weight ;.
Preferably, the total polymer content in the reservoir is between about 2 % and 50 % by weight.
The dispersed copolymer phase comprises from 5 to 50 weight % of the total polymer composition.
In another aspect, the total polymer weight percentage is about 42 %.
Cont would terpene monomers account for 95 % or more by weight of the total polymer content.
In one aspect, the total polymer weight percentage is about 40 %.
An advantageous material for said bag comprises, in weight % based on the total polymer weight,.
In general, from 5 to 60 % of the total polymer is produced in the first reactor.
The isotacticity is determined by 13C-NMR analysis on the total polymer.
Preferably for optimal taste masking effect, total polymer to drug ratio is at least 1:4.
The isotacticity was determined by 13C-NMR analysis on the total polymer.
Process according to claim 1 wherein the total polymer concentration of the solution is between 10 and 18 %.
Especially preferred compositions will contain 1 to 25 wt. % of total polymer content.
Solutions according to claim 1, characterised in that the total polymer concentration is between 15 and 20 %.
In total, the ethylene oxide content is from 8 to 30 percent of the total polymer.
This process was repeated 3 times to achieve a total polymer loading of 25 %.
This third monomer, the termonomer, is present up to 10 wt % of the total polymer weight.
The fraction of the high MFR material in the total polymer was thus 48 %.
The amount produced of ethylene-isobutylene copolymer was less than 1.3 weight % of the total polymer products.
The first fraction comprises 95 to 60 weight % of the total polymer composition.
The fraction of high MFR ( low MW ) material in the total polymer was thus 40 %.
You'll also be interested in:
Examples of using Total
Show more
What you did was total and utter betrayal
Total separation between product and propellant
As percentage of total number of cleared cases of arrest
Examples of using Polymer
Show more
Injected polymer compound shell in three sizes
We seem to be a bit light in the polymer sciences
High resistance polymer flow indicator cover
