Examples of 'transformation temperature' in a sentence
Meaning of "transformation temperature"
transformation temperature: This term is commonly used in physics and materials science to refer to the temperature at which a material undergoes a phase change, such as solid to liquid or vice versa
How to use "transformation temperature" in a sentence
Basic
Advanced
transformation temperature
The variation of hardness with transformation temperature was measured.
Transformation temperature range.
Ni is an element for lowering remarkably the transformation temperature.
As was to be expected the transformation temperature increases as the rapid cooling is delayed.
Mn also has the effect of decreasing a transformation temperature.
The mean transformation temperature of each slice, given by.
The nature of bainite changes as the transformation temperature is lowered.
The transformation temperature depends on the nature of the resin and is, for example,.
The transformation takes place quickly once the transformation temperature has been attained.
When the martensite transformation temperature increases, automatic tempering ( auto-temper ) easily occurs.
In this experiment every sample could be heated to a temperature higher than its transformation temperature.
This coiling temperature CT comes close to a bainite transformation temperature for the aforementioned chemical composition.
Temperature maintenance chamber for the wires which have reached the said perlitic transformation temperature.
Furthermore, it lowers the bainite transformation temperature to refine the bainite structure.
The properties of a given shape memory material typically vary within the transformation temperature range.
See also
Although the α-β transformation temperature is nominally, impurities e . g.
The inclusion in the alloy of additional elements can alter the transformation temperature further.
Thus, the Ac1 transformation temperature is set as the upper limit.
This shows that the proof strength of each alloy gently declined with increasing transformation temperature.
It only slightly decreases the martensitic transformation temperature when the Co content is less than 6 %.
The phase change material stores latent heat during a phase transformation occurring at a phase transformation temperature.
SrO is generally used to increase the transformation temperature Tg of the glass.
The A3 transformation temperature is obtained by ( 3 ) Expression above.
Mn provides solid solution strengthening and suppresses the ferritic transformation temperature and ferritic transformation rate.
The measured martensitic transformation temperature Ms thereof is preferably greater than or equal to 100 ° C.
Surface area of the slice k Total surface area of the cylinder Mean transformation temperature.
Its measured martensitic transformation temperature Ms is preferably greater than or equal to 100 ° C.
It is the essential tool in fine-tuning the transformation temperature.
Its measured martensitic transformation temperature Ms may be greater than or equal to 140 ° C.
After hardening, highstrength steels are stressrelieved below the lower transformation temperature.
The measured martensitic transformation temperature Ms thereof may be greater than or equal to 140 ° C.
Nitinol exhibits both properties ; superelasticity is exhibited above the transformation temperature.
The martensitic transformation temperature is then situated between 30 and 40°C.
However, the alloying elements shift the transformation temperature up or down.
Accordingly, the transformation temperature is generally not less than about 800°C.
Note that, the lamellar spacing of the pearlite structures depends on transformation temperature.
Here, Ar3°C is an Ar3 transformation temperature obtained by the following Expression 1.
A combination of both structures, to varying degrees, exist within the transformation temperature range.
Here, Ac1°C is an Ac1 transformation temperature obtained by the following Expression 2.
At this time, when a prior austenite grain is large, an apparent martensite transformation temperature increases.
On the other hand the range of the transformation temperature is somewhat greater ( 18 C instead of 11 C ).
Further, the homogenization treatment also involves homogenization of the martensitic transformation temperature Ms.
Two crystal modifications exist with a transformation temperature of 1289 degrees Celsius.
The final finishing temperature of hot-rolling is made the Ar3 transformation temperature or more.
The measured martensitic transformation temperature Ms was 220 ° C.
Locking members 26a, 26b have an inner diameter D6 when at a temperature below the transformation temperature range.
Passage of the temperature below the austenitic transformation temperature of the material then causes,.
A criterion for this purpose is the so-called transformation temperature Tg.
Terbium exists in two crystal allotropes with a transformation temperature of 1289 °C between them.
The finish rolling temperature is therefore preferably the Ar3 transformation temperature or greater.
You'll also be interested in:
Examples of using Transformation
Show more
A profound transformation is under way in international relations
It like the ultimate transformation and shit
Transformation of statistical regions into regional authorities
Examples of using Temperature
Show more
Manufacturer of the separate temperature measuring equipment
Actual temperature below low temperature value
Select the desired temperature with and
