Examples of 'values in table' in a sentence
Meaning of "values in table"
values in table: This phrase is used in the context of data analysis or database management. It refers to the information or data stored in a structured format within a table
How to use "values in table" in a sentence
Basic
Advanced
values in table
All values in Table III are in parts by weight.
The deviations relate to the values in Table III.
The parenthetically enclosed values in Table I were extrapolated to concentrations below the lowest calibration standard.
The results are given as mean values in table 1.
The values in Table I correspond to set profiles of fibres.
The applied chewing gum formulations are provided according to the values in table 2.
The values in table 1 are taken after stable conditions has been reached, after each addition.
Fiber length is represented by a series of three values in Table 3.
The values in Table 1 below are given as illustrations.
The results are presented as dilution factor values in Table 1.
These values in Table 5 were an average of four belts.
This stratification resulted in the prognostic accuracy values in Table 4.
The numerical values in Table 1 are parts by weight.
The results are reported as an average of the three values in Table 1.
The anisidine values in Table 3 were higher than expected.
See also
Compliance approved or disapproved shall be decided according to the values in Table 1.
The values in Table 6 were an average of two or more belts.
Sensors shall have an accuracy at least as good as the values in Table 5.
All numeral values in Table 1 are expressed as part by weight.
Sample diagram and map presenting the indicator values in Table 1.
All reported values in Table 1 are an average of three replicate tests.
Pharmacokinetic data for all subjects are given as mean values in Table 1.
The emission intensity values in Table 1 are based on a normalized scale.
Values in Table 2 show the scores of the keratinized state of cornea.
For a complete pulse compression convolution, the values in Table 2 should be doubled.
The values in Table 1 are weight parts or dry parts by weight.
It should be noted that the voltage values in Table 2 are for illustration purpose only.
The values in Table 1 were derived from the following parameter values.
Mass loss means a loss of mass that exceed the values in Table 1 below.
The values in Table 5 are derived from the formula below.
Standard burdens for voltage transformers shall be according to the values in Table 3 below.
The values in Table 1 lead to consistent results for comparable conditions.
Mass loss means a loss of mass that exceeds the values in Table 1 below.
The values in Table 2 were generated with the aid of published data.
Figure 2 plots the nickel probe measurements against the alkaline solubility values in Table 1.
Expected values in Table 5 were calculated according to the Hardy-Weinberg equilibrium.
The pH values calculated from the above equation are compared with experimental values in Table 6.
Values in Table 2 also show that less than a quarter of the workers in.
The chemical composition based on the ladle analysis shall comply with the values in Table 1.
The values in Table 6 represent the load when the material failed.
The latter is also shown by low Ne values in Table 2.
The numerical values in Table 1 are in grams of emission per kilometer of vehicle travel.
This test was used to determine the K values in Table 2.
The summarized values in Table 2 are the overall carbon allocations across both processes.
The feed composition is similar to the values in Table III, column A.
The bypass values in Table 1 represent an evaluation of a single sample for each treatment.
The individual data points are also listed as values in Table 12.
The values in Table 3 below show the results of the fuel efficiency test.
Eliminate access points whose values in table have not been updated ( value equal to 0 ) ;.
The values in Table 2 apply for the tensile strength of spring hard rolled strip.
You'll also be interested in:
Examples of using Table
Show more
The latest tour de table is publicly available
Table i drivers of satisfaction related to access to services
Replace the table with the following
Examples of using Values
Show more
The measured values shall be plotted on a graph
Date and time revert to default values
Carrying values and estimated fair values
