Examples of 'absorbance readings' in a sentence
Meaning of "absorbance readings"
absorbance readings: In scientific experiments or analyses, absorbance readings refer to measurements of the amount of light absorbed by a substance, often used in spectrophotometry to determine concentration or purity
How to use "absorbance readings" in a sentence
Basic
Advanced
absorbance readings
Absorbance readings were measured using a spectrophotometer for microtiter plates.
Asphaltene stability is than calculated based upon the absorbance readings.
Enter the absorbance readings in the provided spreadsheet for analysis.
An electropherogram is generated showing peaks corresponding to absorbance readings at particular migration times.
The absorbance readings were plotted against the test peptide concentration.
Prepare a calibration graph by plotting the net absorbance readings against milligrams of niobium.
The absorbance readings were quite close and so the result was deemed to be accurate.
Prepare calibration graphs by plotting the net absorbance readings against milligrams of titanium.
Absorbance readings are normally taken at regular intervals during this incubation period.
A high concentration of the protein to be detected in the sample causes higher absorbance readings.
The absorbance readings were integrated to give values of área under the curve.
Prepare the calibration graph by plotting the net absorbance readings against micrograms of phosphorus.
Absorbance readings for both assays were carried out using a microplate reader.
The proliferative effect of each test condition was evaluated by comparing the absorbance readings measured.
Absorbance readings of at least twice the value of the negative controls were considered positive.
See also
Cytotoxicity results have been corrected by subtracting the absorbance readings due to the dilution medium.
The difference in absorbance readings correlates with the quantity of ammonia in the sample.
Less protein in the sample results in less enzyme activity and consequently lower absorbance readings.
Absorbance readings from the wells in each plate were compared to a negative control well.
Dose response curves were generated from the absorbance readings using Origin Software.
Samples with absorbance readings greater than or equal to the Cutoff Value are presumptively positive.
In the following Table XXX provides the absorbance readings for solvent extracts,.
Absorbance readings and data calculations are performed on a Molecular Devices plate reader.
Each standard was tested six times, and absorbance readings were averaged to obtain a mean absorbance.
Absorbance readings were started 30 seconds later for a kinetic rate determination.
The plate map and absorbance readings are in Figures 7 to 9.
Absorbance readings were then normalised to absorbance / disk weight to eliminate differences between disks.
This may explain the minor deviations in the absorbance readings ( Figure 2 ).
The difference in the two absorbance readings constituted the signal generated by the sample.
The dispersants and dispersants with MEKO values are the average of 2-3 absorbance readings.
True absorbance readings were obtained by subtracting a blank control ( no enzyme ) from each value.
Rates were determined using the 5 absorbance readings of cycles 11 through 15.
The absorbance readings were then placed into equations 1 or 2 to obtain the concentrations of MTX.
In this case, steps 13 to 15 were carried out to obtain clearer absorbance readings.
Absorbance readings were taken on the spectrophotometer at 520 nm and correlated to amount.
The plates were then placed in the incubator at 37 ° C. and absorbance readings were taken 3 h.
A280 absorbance readings were taken at the beginning and end of the exchange.
Plates were then shaken and absorbance readings at 540 nm were determined using a plate reader.
Absorbance readings were taken after 10 minutes using a microtitre plate reader ( Titertek Multiscan ).
During the assay, absorbance readings at 340 nm were made at the end of every cycle.
Absorbance readings were obtained using the Mithras LB940 plate reader system.
Thereafter, absorbance readings were taken on a plate reader at a 490nm wavelength.
Absorbance readings at 640 nm were taken after two minutes.
The resultant absorbance readings were analysed by a statistical package ( SAS Institute 1997 ) to determine titre.
Absorbance readings were taken every 0.5 seconds.
Figs 8 and 9 show absorbance readings against wavelength for a normal formulation ( Fig 8 ) and a DMSO formulation ( Fig 9 ).
Absorbance readings were taken at 630 nm after 3 hours of incubation.
Figure 3 shows absorbance readings at 260nm of solutions containing R4 and DNA.
Absorbance readings are spectrophotometrically measured at 590 nm.
You'll also be interested in:
Examples of using Readings
Show more
And magnetic readings are still the same
Readings were not consistently taken at heart level
These poetry readings always run long
Examples of using Absorbance
Show more
Absorbance ratio of colour bound by phosphoryl cellulose
You measure absorbance just like that
Absorbance of the measuring solution at the maximum
