Examples of 'amplifier output' in a sentence
Meaning of "amplifier output"
amplifier output - 'Amplifier output' refers to the electrical signal that is produced by an amplifier in response to an input signal. It is the amplified version of the original signal, which is then sent to a speaker or another output device
How to use "amplifier output" in a sentence
Basic
Advanced
amplifier output
This adjusts the level of amplifier output.
Because the amplifier output has short circuited.
Because there is a shortcircuit at the amplifier output.
Connect the amplifier output or the output of the.
There is a short circuit at the amplifier output wires.
The amplifier output becomes disabled.
Power of the speakers exceeds the amplifier output power.
The amplifier output impedance is also assumed to be totally resistive.
Saturated power amplifier output.
The amplifier output is fed to the splitter through coaxial trunk lines.
One basic principle is to feed back the amplifier output.
The two jacks of the power amplifier output are connected in parallel.
The amplifier output is sampled from the output of the last stage.
A small amount of noise can cause the amplifier output to rise slightly.
The new amplifier output signal serves as the power on reset signal.
See also
Do not parallel or series connect an amplifier output with any other amplifier output.
The amplifier output voltage is thus proportional to the temperature of each detector.
This adjusts the level of amplifier output when using the clean channel.
All the reactive capacitive current flows through the amplifier output devices.
Radar amplifier output.
Barrier strips located on the rear panel allow speaker cable connections to the amplifier output.
This adjusts the level of amplifier output when using the overdrive channel.
The amplifier output level is controlled by the output signal of the control voltage generator.
The amplified distortion is injected into the main amplifier output to cancel the distortion component.
Most power amplifier output stages are supplied by passive and unregulated voltage rails.
The respective idle operating points in the respective differential amplifier output stages are thereby displaced.
The power amplifier output power is from an amplifier with the seven traverses power amplifier.
The voltage VS available at the amplifier output is output at high impedance.
The Clip indicators turn on when distortion is audible in the amplifier output.
Outside that range the amplifier output stage goes into saturation and can work as a comparator.
These IM products are then output as part of the amplifier output signal.
The amplifier output will be muted whilst in Tuner Mode.
TIM distortion was found to occur during very rapid increases in amplifier output voltage.
If amplifier output wires develop a short-circuit.
In a frequency modulation transmitter, the power amplifier output is connected to the,.
Should the amplifier output stage become non-operational.
Therefore, over time or after prolonged use, the quality of the amplifier output may deteriorate.
Amplifier output stage provided with a parasitic-current limiter.
When the measurement is complete, amplifier output correction will be automatically turned on.
The amplifier output is connected to a standard circuit 21 forming a driving pulse generator.
There are two ways to wire the amplifier output connectors for Bridge-Mono mode.
The amplifier output is also connected to an output driver stage 13 comprising a rectifier and a transistor.
Unlike a conventional servo design, the shaping amplifier output is routed to two independent outputs.
For the amplifier output connectors is recommended to use high-quality cable.
It therefore relies on reasonably accurate calibration of the UE 's power amplifier output.
The sampled output from the main amplifier output is attenuated and applied to point 50.
Additionally, a single Master volume knob controls the final amplifier output level.
Each amplifier output is coupled to a low pass filter ( LPF ) exhibiting an appropriate frequency response.
In this way, the output noise of DDA2 is added differentially to the amplifier output.
Output Current Limiting circuitry protects the amplifier output stage from damage caused by short-circuit loads.
You'll also be interested in:
Examples of using Amplifier
Show more
Make sure that the amplifier is switched on
Amplifier is picking up alternator noise or radiated noise
Never operate the amplifier without cover
Examples of using Output
Show more
One output will contribute to this outcome
Illuminates when output is sent to the tray
Output signals common to measuring technology are available
