Examples of 'braking torque' in a sentence
Meaning of "braking torque"
Braking torque refers to the force or twisting motion exerted by a braking system on a rotating object, such as a wheel or rotor, to slow down or stop its rotation. It is a measure of the braking effectiveness or stopping power
How to use "braking torque" in a sentence
Basic
Advanced
braking torque
Braking torque activating the overload protector.
This causes a quick rise in braking torque.
Increases the braking torque by decreasing speed.
This delays the rise in braking torque.
Braking torque at which the overload protector is activated.
One sensor to measure the braking torque.
Maximum braking torque of the brakes.
Referring to the effective braking torque.
Braking torque changed during operation.
Under dynamic loads the braking torque is reduced.
The braking torque on the drive shaft is thus increased.
All of these factors affect the braking torque.
Braking torque is only available if lines of magnetic flux are cut.
Check adequacy of motor braking torque.
Applying the braking torque command to the power train brake.
See also
Actuating the emergency release nullifies the braking torque.
These values correspond to braking torque values as explained here above.
We then pass to the step of determination of a theoretical braking torque.
Braking torque when the trailer moves rearward including rolling resistance.
Escalator caliper brake assembly with adjustable braking torque.
The braking torque depends on the corresponding runningin condition of the brake.
The number of the plates depends on the desired braking torque.
For restricted braking torque tolerances please contact mayr power transmission.
The auxiliary brake can be designed to exert an adjustable braking torque.
Its braking torque being controlled by the phasing of the switching of the command.
Then the vehicle is decelerated at deceleration corresponding to the braking torque.
The braking torque obtained in either sense of rotation is approximately the same.
The braking resistor may increase the braking torque of the inverter.
The braking torque is inversely proportional to the brake fluid pressure applied.
Braking method for hybrid vehicles compensating for an electric braking torque.
In this way a higher braking torque is achieved in case the brake fails.
Thus the brake used must be capable of developing a high braking torque.
The brake and the achieved braking torque must be tested in the application.
A state indicated by a solid line is maintained because the braking torque is great.
The braking torque exerted by the suspension arms acts to increase this force.
The rigid section absorbs the greatest portion of the braking torque.
Braking torque detected by the braking torque detecting device corresponds to pushing force.
This can lead to breakage of the toothing and therefore to a loss of braking torque.
Increasing the delay time or reducing the braking torque is only possible to a limited extent.
The method may also include identifying a maximum available regenerative braking torque.
A cyclic braking torque test of the brake rotor during operation provides additional safety.
This distribution can ensure that the requested braking torque is actually applied.
Regenerative braking torque fay the electric motor that can be proportioned by the driver.
This friction brakes the load and is added to the braking torque of the spring.
The braking torque produced and applied to the drive shaft slows down the vehicle.
In comparing the corrected value of the braking torque with a control value of this torque.
A knowledge of the phase currents is important for accurate control of the active braking torque.
A motor operating as a generator generates a braking torque which can be used to compensate system losses.
An electronic unit converts the optical signals to electrical signals representative for the braking torque.
This induces an electrical braking torque which opposes the momentum of the fan and motor.
You'll also be interested in:
Examples of using Torque
Show more
The resulting torque introduces the rotation
Torque for terminal box cover screws
Low level inducement torque reduction scheme
Examples of using Braking
Show more
Hydraulic braking systems with stored energy
Restriction to free movement of the braking system
Distribution of braking among the axles of vehicles
