Examples of 'crosshead speed' in a sentence
Meaning of "crosshead speed"
crosshead speed: a term often used in the context of machinery or engines, referring to the speed of a reciprocating engine's piston in relation to the crankshaft. It is an important factor in determining the efficiency and performance of the engine
How to use "crosshead speed" in a sentence
Basic
Advanced
crosshead speed
Crosshead speed of the testing machine.
The tensile test uses a crosshead speed of two inches per minute.
Crosshead speed in testing machine.
Shear bond strength was evaluated in a universal testing machine at a crosshead speed of 1 mm / min.
The samples were run at a crosshead speed of 12 in / min in the tensile direction.
The speed for modulus determination shall be set at a crosshead speed of 1 mm / min.
The crosshead speed of the electromechanical testing system is set at 50 mm / min.
Shear bond strength testing was performed after storage times at a crosshead speed of 1 mm / min.
Crosshead speed was 2mm/min for determining the flexural modulus.
The microtensile test was carried on a universal testing machine operated at a crosshead speed of 1mm/min.
All tensile strengths are for a crosshead speed of 0.2 inches per minute.
The crosshead speed of the instron was set at 40 inches per minute.
The bond strength was determined using a Tensile testing machine at a crosshead speed of 2 mm / min.
The specimens were tested at a crosshead speed of 0.5 mm / min on a universal testing machine until failure.
The tubes were measured at room temperature at a crosshead speed of 10 mm / minute.
See also
Set the Testing Machine crosshead speed and the chart speed at 20 inches / minute.
The films were measured at room temperature at a crosshead speed of 10 mm / minute.
The crosshead speed was set at 2 mm / min.
Samples were pulled apart at a crosshead speed of 2 inches / minute.
Insert the specimen tightly into the crosshead jaws, and use a 4 in . / min crosshead speed.
Specimens were crushed at a crosshead speed of 1 mm / min.
Mechanical properties of the reformed fibroin filaments were measured on 2 cm lengths with a 250 % crosshead speed.
The tensile test is run at a crosshead speed of 2 in / min.
The crosshead speed was 2mm/min.
The tensile strength was determined at a crosshead speed of 50 mm / min.
The crosshead speed was 508 millimeters per minute.
Sbs was performed in an instron at crosshead speed of 1 mm / min until failure.
Crosshead speed and the chart recorder speed were set to 500 mm / min.
A tensile tester was set up with a crosshead speed of 0.5 inches per minute.
At a crosshead speed of 500 mm / min. the average force was recorded to completely delaminate the sample.
The bond was stressed until failure, using a crosshead speed of 2 mm / minute.
Deformation was performed at a constant crosshead speed of 5.0 in / min with a data sampling rate of 25 points / second.
The tensile strength was determined using a tensometer at a crosshead speed of 50mm/minute.
The samples are then pulled apart at a crosshead speed of 8 inches / minute with a 8 " gap.
The tensile properties were measured using a tensometer at a crosshead speed of 50mm/minute.
The Instron was set with a crosshead speed of 300mm per minute.
Three specimens were tested for each cable sample at a crosshead speed of 50 mm / minute.
The sample is tested at a crosshead speed of 20 cm / min.
The shear strength was evaluated using a tensile tester operated at a crosshead speed of 2.5 mm / minute.
Shear bond strength was measured using a crosshead speed of 1,0 mm / min.
Tensile properties were measured using an Instron tensile tester with a crosshead speed of 500 mm / min.
Each conductor was pulled out of the encapsulant at a crosshead speed of about 0.8 mm / sec.
All samples were tested on a Zwick tensile tester using a crosshead speed of 2 mm min-1.
The test parameters included a gauge length of 40 mm and a crosshead speed of 2 mm / min.
Each bar was broken on a Tinius-Olsen testing machine at a crosshead speed of approximately +.250.
Each sealed sample was peeled apart at a 180 ° angle at a crosshead speed of 1 inch per minute.
The shear strengths were measured using a JJ Lloyd tensometer, with a crosshead speed of 125 mm / minute.
You'll also be interested in:
Examples of using Crosshead
Show more
A three bar crosshead was added to the motion
These engines typically use crosshead pistons
Use a suitable crosshead screwdriver to remove this clamp
Examples of using Speed
Show more
The speed of the vacuum source shall be
I must have hit speed dial by mistake
Zoom speed is determined by the amount of rotation
