Examples of 'cut-off frequency' in a sentence
Meaning of "cut-off frequency"
cut-off frequency: this phrase is commonly used in the field of signal processing or electronics to denote the frequency at which a signal or a system starts to attenuate or block certain frequencies. It represents the boundary or threshold frequency beyond which the amplitude or power of the signal decreases significantly or falls below a certain level.
How to use "cut-off frequency" in a sentence
Basic
Advanced
cut-off frequency
Analytic formulation of the cut-off frequency.
The loop cut-off frequency is an important parameter.
Controller to control the upper cut-off frequency.
Determining the cut-off frequency of a finned waveguide.
The filter is characterized by a slope and a cut-off frequency fc.
Adjusting the cut-off frequency for the subwoofers.
Field effect transistor with a high cut-off frequency.
Adjusts the cut-off frequency and subwoofer phase.
This condition imposes the sought cut-off frequency fc.
Modification of a cut-off frequency in the filtering of the signal.
The calculations for estimating the filter cut-off frequency f.
The cut-off frequency is adapted to the measured noise.
Frequency range upper cut-off frequency is variable.
The cut-off frequency increases as the air gap increases.
The same occurs if the cut-off frequency is high.
See also
The cut-off frequency scaling factor may be a default value.
Those harmonics above the cut-off frequency are sharply attenuated.
The cut-off frequency is changed to prevent the propagation of low frequencies.
For this reason the cut-off frequency changes with speed.
The cut-off frequency below which a signal is considered voiced is updated.
These values are selected to define a cut-off frequency in a high range of frequencies.
The cut-off frequency defines the lower end of user bandwidth.
Only frequencies that are below the cut-off frequency are passed on to the loudspeakers.
The cut-off frequency is dependent on the time based frequency of the samples.
This leads to a transfer function with a cut-off frequency rejected at high frequency.
Select the cut-off frequency up to which higher frequencies should be blocked.
The frequency control changes the upper cut-off frequency of the subwoofer.
What is the cut-off frequency of a moving average filter.
The higher the noise level the larger the cut-off frequency.
Note that this cut-off frequency is a typical example.
It also attenuates those signals whose frequency is higher than the cut-off frequency.
Adjusts the cut-off frequency of the high pass filter.
The damping itself has a transfer function with gain and a cut-off frequency.
Adjusting the cut-off frequency value and the slope value.
The value of the capacitor is then conditioned by the value of the cut-off frequency.
The difference in cut-off frequency may be a factor of two or even more.
This formula expresses that the frequency is very close to the cut-off frequency.
Or to increase the cut-off frequency while maintaining the same output power.
This is the case when a very low and selective cut-off frequency is required.
Increasing the cut-off frequency is known to increase the cost of the component.
The damping produced by each loop is additional while maintaining an unchanged cut-off frequency.
Knob for adjusting the upper cut-off frequency for the subwoofer unit.
The cut-off frequency of the high pass filters for both stereo chan.
However, this mobile telephone has a cut-off frequency band in the audible spectrum.
The cut-off frequency determines the point at which the filter starts to work.
This will allow you to select the cut-off frequency for each band.
Cut-off frequency determines after which part the filter will start cutting.
However, the emitter potential barrier height seriously limits the cut-off frequency.
Adjust the cut-off frequency to the front / rear speakers according to the subwoofer setting.
Field effect transistor with high cut-off frequency and process for forming same.
You'll also be interested in:
Examples of using Frequency
Show more
Adjusts the higher frequency of the sound
The frequency of armed conflicts is on a downward trend
The desired station frequency is not tuned in
Examples of using Cut-off
Show more
The cut-off has been automatically activated
Geographical localities are selected by cut-off sampling
Of air cut-off pneumatic screwdrivers with
