Examples of 'full turns' in a sentence
Meaning of "full turns"
The phrase 'full turns' is commonly used in the context of dancing or gymnastics. It refers to a complete rotation or spin executed by a performer. The term emphasizes the completion of a circular movement, indicating that the individual has completed a full rotation
How to use "full turns" in a sentence
Basic
Advanced
full turns
Turn two full turns on each screw.
Leave enough slack to allow full turns.
There are two full turns of adjustment available from full clockwise.
Loosen screw at least three full turns.
There are three full turns of adjustment available from full clockwise.
Loosen clamp lever approximately six full turns.
Full turns in between.
Loosen clamp lever ap proximately six full turns.
Full turns correspond to the maximum dose to be administered in one injection.
It therefore forms a coil comprising several full turns.
Two full turns.
Unthread the internal seal head three full turns.
Wrap the tape two full turns around the vent pipe.
Install the body bolt into the caliper two full turns.
At least two full turns of cable will remain on drums at all time.
See also
The safety chain should be hooked long enough to permit full turns.
Compression valves require several full turns to open the valves fully.
Unthread the poppet valve cover from the poppet valve housing three full turns.
It indicates the number of full turns that the crank makes in one minute RPM.
Align the caliper body halves then install the caliper body bolts two full turns.
There are only 3 full turns from minimum to maximum preload.
Turn orifice hood counterclockwise 2 full turns.
Extend all 4 feet by three full turns before moving the machine to its final position.
Turn the high speed needle valve counterclockwise 2 full turns.
Then open it two full turns clockwise standard setting ID 2.
Turn handle counter-clockwise no more than two full turns.
Three full turns of adjustment nut will change mower height about 1/8.
Preferably, the loops of the ring describe at least two full turns.
Here, this track makes several full turns before reaching the via 68.
Fully tighten the locknut, then loosen the nut two full turns.
Full turns in between . You will here a loud " click " when you are done.
Depressurize system by opening release valve counterclockwise, but no more than 2 full turns.
Thread a 2-pronged knob onto the bolt two full turns while leaving it loose.
Turn the zero set knob counterclockwise until it stops, then turn clockwise 3 full turns.
Full turns in between. You will hear a loud click when you're done.
Thread the nozzle onto the spindle until you feel a little resistance about 10 full turns.
Loosen rear plate screw six full turns using the 6/4mm hex key.
Loosen locknut ( 1 ) by turning counterclockwise several full turns.
Here, the track 216 makes several full turns around each winding axis.
To remove lamp shade, loosen set screw 2 full turns.
Turn drain hose knob counter-clockwise approximately three full turns and pull out plug to drain.
Loosen the axle nut ( b ) on both ends of the flywheel axle two full turns.
The trip takes approximately 15 minutes, during which the wheel makes three full turns.
To provide maximum workpiece support when cutting smaller pieces, loosen the knob ( K ) three full turns.
To adjust the height turn the adjustment knob 5-6 full turns.
Preferably, the work coil has between 3 and 6 full turns.
The baseline high-speed needle valve setting for initial start-up is 2 1/4 full turns from closed.
Tire's valve stem was unscrewed. - Two full turns.
You'll also be interested in:
Examples of using Full
Show more
The world was full of startling new concepts
Full transition to new system of administration of justice
They are always full of coy little tricks
Examples of using Turns
Show more
A cocoon which turns them into adults
Turns out to be just an ordinary cigar box
Turn two full turns on each screw
