Examples of 'inventive examples' in a sentence
Meaning of "inventive examples"
inventive examples - creative instances or illustrations that showcase original ideas or solutions
How to use "inventive examples" in a sentence
Basic
Advanced
inventive examples
The inventive examples and comparative examples were evaluated comprehensively.
It was confirmed that any of the inventive examples had an excellent workability.
The inventive examples have an excellent balance of polymer properties.
The morphology of the catalysts of the inventive examples is also uniform.
The inventive examples have the claimed balance of polymer properties.
Hence the visually assessed whiteness of the inventive examples is consistently strong to very strong.
The inventive examples are shown to exhibit improved elastic recovery at elevated temperatures.
The resulting slurry was then collected as the catalyst used in the following inventive examples.
The figures and inventive examples here are not to be interpreted as restricting the invention.
The polyether polycarbonates of the inventive examples of the Hinz et al.
These inventive examples and comparative examples were prepared by the process described below.
Said variations can not achieve a balance of properties as in the inventive Examples.
The control and the two inventive examples were compared as described further below.
The films were formed in a similar manner as described for the Inventive Examples.
This is suggestive that the inventive examples will desirably provide low irritation.
See also
Inventive examples and comparative examples will be used below to illustrate the present invention.
Additionally the compositions of the Inventive Examples have clearly lower emissions.
The inventive examples can also be extrusion coated at high speeds and high temperatures.
Polymerization condition of Inventive examples and Comparative examples.
The inventive examples had among the best impact properties of all samples tested.
Peel test results comparing Madico film with Inventive Examples.
It can be seen that the inventive examples show clear advantages in low temperature impact.
Table 3 summarizes a number of comparative examples and inventive examples.
The eight inventive examples which met or exceeded the yarn quality limitation were woven sizeless.
In contrast, no discoloration and no development of odour occurs in the inventive examples.
Inventive Examples of the present invention will be described below.
Thus the starting material for step a in inventive examples 3 and 4 was a dry polymer mass.
The inventive examples show unusual and unexpected results when examined by TREF.
Therefore, the dye-sensitized solar cells of the inventive examples were excellent in sealing property.
Next, inventive examples will be described in conjunction with comparative examples.
Procedure 1 is the preferred procedure for the inventive examples using the inventive composition.
The inventive examples have even lower hexane-extractable levels.
This indicates that the printing plate precursors according to the inventive examples have a better clean-out.
These four Inventive Examples were woven sizeless.
In direct contrast, none of the inventive examples Ex.
Figure 9 shows the inventive examples as boxes highlighted with arrows.
The G ′ value is still lower than what was reach with the inventive examples.
Next, inventive examples according to the present invention and a comparative example will be explained.
Temperature profiles of the comparative and inventive examples are shown in Figure 6 and Figure 7.
In some non inventive examples of the method, the musculo-skeletal implant is a joint prosthesis.
A catalyst prepared as described above for the Inventive Examples was modified with vinylcyclohexane ( VCH ).
Inventive examples 1 and 2 have been prepared using two loop reactors and one gas phase reactor.
Figure 1 clearly shows, that the inventive examples have higher DDI at a given Draw down ratio.
Table 11, Additional information of the comparative and inventive examples.
Following inventive examples explain the method of step-by-step conditioning of supercapacitors for increased working voltage.
Characterization of ARU, SRU and DP for these inventive examples is shown in Table 1 above.
In the following inventive examples 80 ppm Ti were sufficient at comparable process times.
The other properties are at best for inventive examples 2 and 3.
These inventive examples were prepared as shown in Table 1 and described below.
The following methods were used in forming inventive examples 1-8 described herein.
You'll also be interested in:
Examples of using Inventive
Show more
Your inventive skill is being put to the test
Local staff are outstandingly inventive in accomplishing repairs
The inventive nanoparticles find different applications
Examples of using Examples
Show more
Examples of outcomes and indicators to be tracked include
The following are some examples of mess traditions
Examples of efficiencies gained in coordinating meetings include
