Examples of 'jam nut' in a sentence
Meaning of "jam nut"
Jam nut is a term used in mechanical engineering or automotive industries to refer to a type of nut that is tightened against another nut to prevent loosening due to vibration or rotational forces. It is commonly used in applications where securing and locking two nuts together is necessary
How to use "jam nut" in a sentence
Basic
Advanced
jam nut
Tighten jam nut to lock adjustment in place.
Tighten the igniter jam nut securely.
Hex jam nut with drilling hole.
Then tighten jam nut as shown.
Loosen and remove the igniter jam nut.
Tighten the jam nut on each caster.
A jam nut can also be used with the nut if desired.
Retighten the jam nut against the hex rod.
Tighten the compression nut and then tighten the jam nut.
Tighten the jam nut on the auger cable.
Reduce the belt tension by loosening the cable upper jam nut.
Tighten jam nut to hold table stop in place.
Turn the long section two turns and tighten jam nut.
Retighten jam nut to lock the adjustment in place.
Unplug igniter wire and remove igniter jam nut to pull out igniter.
See also
The jam nut should already be on the leveling foot.
The sensor is to be secured with the jam nut instead of the lock washer.
A jam nut or lock nut.
Lock the adjustment by tightening the jam nut against the stabilizer bar.
Tighten the jam nut securely when satisfied that speaker is level.
Connect rod end to pedal and tighten jam nut on rod to secure adjustment.
Loosen jam nut and turn table top left or right to raise.
The front left elevating bolt uses a jam nut that should remain tight.
Tighten jam nut to hold adjustment in place and connect eye bolt.
Screw the leveling foot with the jam nut into the hole provided on the leg.
Tighten jam nut to secure adjustment and reconnect rod end to switch lever.
Hold adjustment nut in position with wrench and tighten jam nut securely against adjustment nut.
Tighten the jam nut down to the support bracket.
After adjusting, make sure the jam nut is retightened.
Retighten the jam nut loosened earlier when proper adjustment is achieved.
Ensure fitting is in line with cylinder, and tighten jam nut on elbow.
Tightening jam nut on leveling feet.
On the underside of the saw, loosen the jam nut JJ.
Tighten the jam nut to secure the cable when correct adjustment is reached.
If contact occurs, adjust downstop screw and jam nut until problem is corrected Figure 4.
Adjust the jam nut and turn the screw clockwise to decrease the depth of cut.
Hot sale low price china fastener hex head nut hex jam nut - Winrock.
Hold the rocker arm jam nut in place as the pivot ball stud is turned.
From underneath burnisher, loosen jam nut A.
Locate the jam nut and lock nut on the front side of the stabilizer bracket.
Loosen the stabilizing bolt and the jam nut using a 10mm wrench.
Unique jam nut and L-bracket mounting option.
Using an open-end wrench, turn the jam nut to the left to loosen it.
Tighten the jam nut snugly by hand . Do not over tighten the nut.
Your mower is shipped with no “ gap ” between drive control cable and jam nut.
Nylon knurled nut acts as jam nut to fix the position of the fine-adjustment screw.
To adjust speed, disconnect eye bolt ( K ) from pedal and loosen jam nut.
Adjuster stud Adjuster jam nut 19 coating of grease.
Hex jam nut with drilling hole - Winrock.
After adjusting, retighten jam nut ( A ) securely against plunger rod.
You'll also be interested in:
Examples of using Jam
Show more
I was in a bit of a jam and he came through for me
Jam as much of that in the wound as possible
It was a great closer to a jam packed learning adventure
Examples of using Nut
Show more
I am kind of a hard nut to crack in that department
A nut who knows a lot about bombs
Loosen the bottom nut to eliminate water
