Examples of 'minutes at a temperature' in a sentence
Meaning of "minutes at a temperature"
The phrase 'minutes at a temperature' typically refers to a specific duration of time that something is subjected to a certain temperature. It is often used in cooking or scientific experiments when specifying how long a certain ingredient or sample needs to be exposed to heat or cold to achieve a desired outcome
How to use "minutes at a temperature" in a sentence
Basic
Advanced
minutes at a temperature
The treatment consisted of immersion for two minutes at a temperature indicated in Table 1 below.
The alignment layer was subsequently thermally treated in an oven for 2 minutes at a temperature of 80°C.
After stirring for 30 minutes at a temperature of 0°C, the cooling means is removed.
The reaction mixtures were incubated for approximately 4 minutes at a temperature of about 37 °C.
After stirring for 30 minutes at a temperature of about 20 ° C. the insoluble material is filtered off.
The resulting article was then heated for three minutes at a temperature of 95°C.
The mixture was stirred for 30 minutes at a temperature of not higher than 5°C.
This takes place using a Kenwood mixer at maximum speed for 3 minutes at a temperature close to 5 ° C.
The reaction medium is heated for 10 minutes at a temperature of 70 ° C. under microwave irradiation.
In a suitable embodiment, the extracted soy concentrate is suspended for 10 minutes at a temperature of 130°F.
The resulting article was heated for 30 minutes at a temperature of 65°C to polymerize the phenolic resin.
The polymer is allowed to contact the metallocenic catalyst for about 15 minutes at a temperature of 40°C.
The poured layer is allowed to cure for 30 minutes at a temperature of 90 degrees Celsius.
The reaction mixture was incubated for approximately 4 minutes at a temperature of about 37°C.
Bake each cake for no more than 6 minutes at a temperature of 180 degrees.
The hydrogen chloride is introduced over the course of 4 hours 30 minutes at a temperature of -8 ° C.
Cooking in fresh water for a minimum of nine minutes at a temperature of 98 °C, plus or minus 3 °C.
The bond was further enhanced by heating the abrasive article for 15 minutes at a temperature of 110°C.
Heating said coated base fabric ply for about 15 minutes at a temperature from room temperature to 93°C ;.
The mixture was subjected to intermediate treatment for 30 minutes at a temperature of 90 °C.
The reaction mixture was stirred for 90 minutes at a temperature of 4°C.
The transfer is carried out in the course of 10 minutes at a temperature below 0 ° C.
Thereafter the mixing was carried out for 3 minutes at a temperature of 200°C.
The entirety is placed in a ventilated oven for 30 minutes at a temperature of 80°C.
A dispersion is produced by stirring the mixture for 30 minutes at a temperature of 80°C.
The monomer and initiator feed were added over 90 minutes at a temperature of 85 °C.
The PB samples were prepared using a press cycle of 5 minutes at a temperature of 170 °C.
Adds a stage before the main wash, lasting about 20 minutes at a temperature of 35 C.
The reaction medium is left to react for two hours 30 minutes at a temperature of 50 ° C.
Typically, curing is permitted to occur over a period of about 5 minutes at a temperature of 175°C.
Ultrasonic degradation was performed for a total of 16 minutes at a temperature not exceeding 35°C.
The reaction mixture was incubated for approximately eight ( 8 ) minutes at a temperature of 35°C.
The sheet to be treated is then heated for about 5 minutes at a temperature of about 180 ° C.
The composition is then left to stand on the locks for 30 minutes at a temperature of 50°C.
Wet packages are tested after soaking them in water for three minutes at a temperature of 72 ± 3°F.
The aforementioned pasteurisation takes place for a period of 2 to 4 minutes at a temperature from 82 to 85°C.
In the present example, the dehydration will last typically thirty minutes at a temperature of 220 ° C.
The adhesive is completely cured in about 60 minutes at a temperature of 40 ° C.
A Hull cell test was performed on this electrolyte at 1A for 10 minutes at a temperature of 25°C.
You'll also be interested in:
Examples of using Minutes
Show more
Just give me a couple minutes to catch my breath
Ten minutes more and we will eat
Just give me five minutes for my article
Examples of using Temperature
Show more
Manufacturer of the separate temperature measuring equipment
Actual temperature below low temperature value
Select the desired temperature with and
