Examples of 'motor pulley' in a sentence
Meaning of "motor pulley"
motor pulley - A motor pulley is a mechanical component used in machinery to transmit power and motion from a motor to other parts of the machine. It is commonly found in engines, vehicles, and industrial equipment
Show more definitions
- A special pulley attached to an axle of e.g. a motor to extract torque.
How to use "motor pulley" in a sentence
Basic
Advanced
motor pulley
Loosen the setscrew on the motor pulley.
Loose motor pulley or pump flywheel.
Slide belt over the motor pulley.
Adjust flywheel or motor pulley so that the belt runs straight.
Zm is the number of teeth of the motor pulley.
Retighten the motor pulley setscrew.
Place new belt around brushroll motor pulley.
Select the appropriate motor pulley and belt by referring to the table below.
Loop the belt around the motor pulley.
Check the motor pulley or rear axle pulley for sheared off or missing cotters.
Readjust and tighten motor pulley set screw.
Turn rotating floor brush by hand several times in the direction of motor pulley.
Refer to the table below to select the motor pulley and belt combination.
Loose motor pulley or pump Retighten pulley and flywheel.
And unbolt the compressor from the motor pulley.
See also
Loose the set screws of the motor pulley and turn the movable flange.
Remove the belt from the brush and motor pulley.
Loop a new belt over the motor pulley and over the end of the agitator.
Remove the belt from the agitator and motor pulley.
Place new belt over motor pulley and stretch other end over the floor brush.
If the drive belt is not around the brass motor pulley.
The motor pulley has a diameter of about half the roll 's.
Turn the belt cover back over the motor pulley.
Check the fan and motor pulley grooves for dirt, clean the pulleys if needed.
Do not allow the belt guard to contact the drive belt or the motor pulley.
Confirm drive belt is slipping on drive motor pulley and front roller pulley.
Hold the belt with your fingers and place the belt onto the motor pulley.
To prevent injury, avoid touching the motor pulley when checking the belt.
When aligned, tighten the hex socket screw on the side of the motor pulley.
It is important to note, however, that the motor pulley is split into two parts.
Loop the drive belt around the sub-platter and then around the motor pulley.
Place the V-belt around the motor pulley and slue the motor to tense the belt.
Clean string, hair and other debris off the motor pulley and.
Rotation of the motor pulley 25 causes the planetary rollers 26 to travel around an orbit.
Red ribbon Brass motor pulley.
Belt used motor pulley, medium Belt used saw pulley, medium.
Clean strings, hair and other debris from motor pulley and drive belt areas.
Place the drive belt around the sub-platter and around the motor pulley.
Slip the blade and the motor pulley ( bottom ) with the.
NOTE, The belt must be centered over the grooves on the flywheel and motor pulley.
The reference numeral 12 designates a motor pulley secured to the motor shaft of the carrier motor 11.
Putting the motor into rotation induces a rotation of the motor pulley 61.
Door motor 4 having motor pulley 5 is mounted on door frame 3.
Install the drive belt, first around the platter, then around the motor pulley.
Belt Guard - Covers the belt, motor pulley and flywheel.
Place the V-belt q onto the V-belt pulley and the motor pulley.
Next, remove the belt from the motor pulley ( 5 ) and reposition in the motor pulley groove 2.
A worm gear 5 having a pulley 6 is rotated by a belt 7 and a motor pulley 8.
Remove nut E, and remove the motor pulley assembly.
Under the tub 2, there is a motor 5a coupled to a motor pulley 18 with a shaft.
You'll also be interested in:
Examples of using Motor
Show more
Motor eye sensors attached to motion detectors
Use of gaseous fuels in motor vehicles continuing
Motor worked to hard drawing extra current
Examples of using Pulley
Show more
Rotate the pulley to be sure it spins freely
Check for a damaged belt or damaged pulley
Pulley and idler not in correct adjustment
